FEP310VQ0 Roper Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Terry from Mountain City, TN
- Parts Used:
- WPW10196405, WPW10196406
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The drip bowls were all caked and corroded.
This wasn't a "repair", but I got an email asking for my story, so here it is. :-)
I followed the owner's manual instructions by pulling out the burner elements, lifting up the old drip bowls, setting in the new ones, replacing the elements.
I followed the owner's manual instructions by pulling out the burner elements, lifting up the old drip bowls, setting in the new ones, replacing the elements.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rhonda from Logan, OH
- Parts Used:
- WPW10308477
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The oven was blowing a circuit.
Unplugged unit from wall.
Unscrewed the two screws on at he back of the oven where the element is attached
Removed old element by pulling apart the connectors.
Attached new element to the connectors.
Replaced cover with the two screws.
Unscrewed the two screws on at he back of the oven where the element is attached
Removed old element by pulling apart the connectors.
Attached new element to the connectors.
Replaced cover with the two screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- frank from pittsburg, TX
- Parts Used:
- WP9762215
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
had for 2 weeks didnot work called for warinty they fixed stoped woking again about 18months later called them got price then bought though you.
first i turned off breaker . then slid out stove .usea cordless screwdriver totake off back then unplug switch then take off knob then take screwes out of front of switch theninstall new one revice method. took me longer to do this then to do the part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lana from WATERVILLE, ME
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven stopped heating, error message stated heating element
Very easy. Pulled the stove away from the wall. Used a screw driver to remove the two nuts to release the heat sensor, disconnected the wire, removed the sensor. Inserted the new sensor, plugged back into the circuit. put the two nuts back.
Beware, if the first time you put the oven on, if the error message comes back up (mine did) push the cancel/off button, wait a few minutes, put oven back on. System probably needed to reset. Mine worked perfectly after.
Beware, if the first time you put the oven on, if the error message comes back up (mine did) push the cancel/off button, wait a few minutes, put oven back on. System probably needed to reset. Mine worked perfectly after.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from BURNSVILLE, MN
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven Temp inaccurate
I watched the repair video on this site and another on YouTube before I started. The rear panel has a different shape and two additional screws on the bottom edge. The power clip was easy to manipulate.
This was an easy fix for a seventy year-old like me!
This was an easy fix for a seventy year-old like me!
Was this instruction helpful to you?
Thank you for voting!
Infinite switch bad and receptacle heat damaged
Removed back plate, replaced infinite switch.
Replaced receptacle holder. Took a moment to see how to install wires into the receptacle, no instructions on orientation of wires into the receptacle. Wired receptacle per instructions. Placed receptacle into holder and installed burner. Burner Burner would not lay flat, receptacle longer than original. Removed receptacle from holder, plugged in burner and placed burner into position.
Replaced receptacle holder. Took a moment to see how to install wires into the receptacle, no instructions on orientation of wires into the receptacle. Wired receptacle per instructions. Placed receptacle into holder and installed burner. Burner Burner would not lay flat, receptacle longer than original. Removed receptacle from holder, plugged in burner and placed burner into position.
Was this instruction helpful to you?
Thank you for voting!
Burned out wires and 2 switches.
Unscrewed the switches and let the switch hang while replacing one wire at a time. Followed instructions on wire replacement. Exact parts, only shaft on 6" switch was too long -- okay, because it is designed to break off a piece on end of shaft, then the knob fit. Everything was perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from PLUM CITY, WI
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
oven not keeping correct temp and sometimes would not relight when temp went dropped.t
Slid oven out and took back shield off unplugged sensor took bracket screw out replaced sensor with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Irving, TX
- Parts Used:
- WPW10196405, WPW10196406
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
piece of cake. The pictures with the grid background on your website gave me ability to verify what I was purchasing.
This is the second use of Parts Select. First time was for another obscure part for an old microwave, which also worked out VERY well. Both appliances still in action.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynn from BRADENTON, FL
- Parts Used:
- WPW10196406, WPW10196405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Drip pans were not original to range, I could not get them clean.
I reoved old drip pans and installed new ones. Very easy, they look great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frances from Summerfield, FL
- Parts Used:
- WPW10196405, WPW10196406
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced old drip pans
Fastest, easiest thing I have ever done! I got my orders so fast it was unreal! Hurrah for good old American know-how. I will always recommend these good people!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- corey from SHAKER HEIGHTS, OH
- Parts Used:
- W10856603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Sparks flying out of the oven, broiler element melting
First Things first, unplug unit, remove rear cover with Phillips head screwdriver, disconnect, wires from broiler element which is the top, one, open oven, unscrew top screws first, then two at the back, wiggle out element, then reverse Steps , test repair before putting cover back on. Then ta-da, you saved yourself a $300. Service call to the appliance repair guy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LOUIS C from GRAND JCT, CO
- Parts Used:
- WP3149404
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dual burner would go to highn heat.
Watched video & did just guy in video did. Very easy job & the burner works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ANN from MANITOWOC, WI
- Parts Used:
- 814399
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Receptacle Assembly Has Burned Out
Remove old receptacle and connected and replace new one. Burner now works perfectly again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marsha from Clermont, FL
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven not reaching temperature
Simple-pulled range away from wall, unplug from socket. Removed back panel unscrewed thermoses and replace. Put back panel back on plug in, tested temperature setting before sliding range back on place
Was this instruction helpful to you?
Thank you for voting!