FGS337GN5 Roper Range - Instructions

Removed two screws holding the bottom in, pulled out old bottom, inserted new bottom, replaced screws and tightened them. Total time less than five minutes.

Unsrewed what was left of the trim and oven handle. Just 4 screws total, then replaced the 2 screws of the trim and the 2 screws on handle.
Finished! Replacement parts fit perfect!!! Thanks a milliion!

Removed two screws and the front of the door popped off. Replaced the bottom metal piece that the glass front slides into. It was a piece of cake.

simple change out - remove old grates, install new ones - note that this site/store is excellent

Removed two gas lines at the safety valve. Removed the four mounting screws and disconnected the three wires. Re-assembled in reverse order of dis-assembly. This was an easy diagnosis and repair/replacement. The PartSelect website is very easy to use if you have the model number and I like the diagrams to be sure the part is correct.

removed door handle screws then removed glass retaining tabs from sides put clips on sides of glass held insuation in place and replaced glass replaced door handle replaced two door screws trial opened and closed door successful done

I had problem with the oven of the stove since the beginning. It wa difficult to start. Later, it stoped working. The technician told m that the gas valve regulator was the problem. That was the reason I decided to buy a new one. After installing it, however, the problem continues. The ignition starts, but the gas does not go thru. It seems the signal does not go to the valve to open the gas.

Our existing gas stove burner igniter had broken on one of the four burners. I therefore obtained a replacement igniter and mounting screw form PartSelect.com which were indeed perfect replacement parts. However, I could not remove the burner plates from the top of the stove since they were basically welded into position by years of heat. I therefore followed instructions as submitted by a previous customer (thank you Michael of Bloomington, Il), snapped open the stove lid retainer clips, and then lifted the stove surface about 4 inches. Through that opening I was able to reach the underside of the involved burner. Unfortunately, I could not unscrew the existing broken igniter mounting screw and therefore had to break off the already broken igniter and grind down the remaining mounting screw using a drill grinder since the screw was basically welded into place. Once I did that, I was then able to install the new igniter using a separate unused screw hole already in place right beside the old previous mounting screw. With that done, the new igniter works perfectly and the burner works just like new. It was however a lengthy process over two hours long because of the glitches described above. Nevertheless I'm very pleased that the parts were perfect and the repair is complete.

Replaced bottom trim included in kit.
Installed side door trim.
While trying to slide glass front in place both plastic side trims broke.
Had to use already broken door trim and glued in. Just hope when use oven glue doesn’t melt and will have to replace entire oven.

Removed drawer, after removing the 50# of junk in the drawer, Used screw driver to remove screw that holds glide to drawer and then place new part into place put screw into hole and tightened screw. Replaced drawer and told wife not to put 50# of junk back into the drawer.

This was a very smooth repair. In total it took about 5 minutes. The pot drawer below the oven wasn't gliding like it once did. After I replaced the glides it works like new. Please note, if you are going to replace one side go the next step and replace both to provide balance to the drawer.

REMOVE BACK COVER. UN PLUG, REMOVE TWO SCREWS IN SIDE OVEN, PULL OUT , REPLACE, REATTACH, FIXED CODE F-3

Simply removed the bottom drawer, unscrew the old broken glide, and attach the new glide. Simple and no hassles.

Remove the side covers. Remove the 2 screws on the back side of the door, hold on to the glass and front panel, they will fall out. remove the 2 screws holding the handle. Put the new handle in place and insert screws, note the old handle had metal inserts that are threaded, the new does not. Had to push very hard and let the screws bite into the plastic.

Loosened two screws and removed tray, very simple. Replaced new tray and adjusted screws to hold tray. Easiest part was finding new tray part number and ordering replacement using online parts diagram.