S9507W1 Roper Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Cody from Abilene, TX
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Surface Burner not working
I lifted the stove top and cut the two wire connected to the block. Attached the new wire connectors, new block and checked to make sure it was working. The part that took the longest was getting the screw out of the mounting brracked(it was corroded on). I sprayed some WD40 and waited 5 minuts, it came loose. Then i mounted the new bracket and installed the burner. double checked everything and lowered the top. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Art from Parma, OH
- Parts Used:
- 8053344
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Bad tempature sensor
Followed instruction on web site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alberto from North Lauderdale, FL
- Parts Used:
- 339392
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The handle on lint filter broke.
Took the old one out and replaced it with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hans R from Midland, TX
- Parts Used:
- 339392
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
1967 Dryer lint screen falling apart (45 years old)
Had to guess at replacement (dryer too old to still be listed) picture and measurements looked right; it was, Old one out--new one slid in, great that it was available.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James R. from Ghent, WV
- Parts Used:
- 285574
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Top half of agitator not turning
Removed old agitator and replaced with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Art from Parma, OH
- Parts Used:
- 8053344
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
F 3 error
I did the repair following your instructions and it went very well. Now the temperature is working good , but the oven is heating up very slow. So now what should I do to fix the oven?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gene from kent, WA
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burner not working
burner was shorting out replaced part works great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from Union Mills, NC
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burner would not heat up the connection was bad
loosened the screw holding the block pulled it out toget to wire cut it about 4 inches long followed the inst.with block kit and it was a breeze. burner working fine now should have did it sooner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Desoto, MO
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
two of the burners were working intermittently
I shut off the breaker checked for power then cut old plugs making sure to allow a little slack. Tightened down wire nuts put on a couple wraps of electrical tape and that was it. Burners work great now I would reccomend this product to anyone with a similar problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Chesapeake, VA
- Parts Used:
- 330031
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The surface burner socket that the burner plugs into melted.
Cut the old wires off, removed the screw holding the clamp, installed the new parts. Problems I encountered were the wire nuts. They were too small for the wire gage of the replacement part and the original oven. I had larger wire nuts in my workshop. Also, why so many extra parts like the shrink wrap tubing, two metal clamps to hold the socket, etc.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim L. from Indian Trail, NC
- Parts Used:
- 339392
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Handle Broke Off Lint Filter
Pulled out old filter. Recycled. Slid in new filter. Closed plastic cover. Voila! Done! No real "repair" involved. More of a replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from San Pedro, CA
- Parts Used:
- 339392
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Plastic handle broke
bought new lint filter and put it in the slot.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Mes, AZ
- Parts Used:
- 339392
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace lint trap..
New lint trap was in good shape and ready to slide into its proper place. Easily done. Works well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sabina from Queens Village, NY
- Parts Used:
- 339392
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lint filter needed replacement.
My 40-ish year old Whirlpool dryer needed its lint filter replaced. You guys had the replacement! Fast shipping and even faster switching out the filter. Thank you PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Villa Ridge, MO
- Parts Used:
- 330031
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
one burner that would not heat and others that would not out out much heat
I noticed that one of the burner blocks was completely burned and the others were corroded. I ordered blocks for all four burners. Installation was easy except for one block. The screw holding the bracket to the range top was completely corroded in place. I used a correct size easy-out, which is a left hand tap and drill, to remove the screw. That took about five minutes, including tracking the easy-out down in one of my many toolboxes. The entire replacement of four blocks took about one and a half hours. Stove top cooks like new on all burners! The part kit had all the right parts and they fit like a glove!
Was this instruction helpful to you?
Thank you for voting!