FGP335GW0 Roper Range - Instructions

It was worth the money for that little screw, since I didn't have to run all over trying to find the right one.

To begin with,the symptoms were strange.....the burner would not ignite even though the igniter was glowing....but if you bumped anything in the broiler or pulled the drawer out and closed it abruptly,it would lite. This went on for a few weeks , until slamming and banging worked no more.(that was getting old anyway)I went ahead and ordered the igniter.It came fast and was very easy to replace.I went in from the oven,took out the racks and the bottom plate(2 screws), exposing the flame diverter that is just above the burner.(2 screws)You can access the igniter now ,and remove it.(2 screws),and unplug it.Reverse order to install the new one.I didnt unplug the range or turn off the power,because I screwed the igniter on first and then it was a matter of just plugging it in. Everything went back together and turned on the oven. Worked fine. Very easy to do,and no more banging around the broiler.Should have done it sooner.

Since the broiler worked fine, I took the igniter from the broiler (exact same) and moved it to the bottom and sure enough oven ignited fine. I did this to isolate the problem, because it could have been either the igniter or the valve. I put the broiler igniter back on top when I got the new part, because it is used only 5% of the time. Be aware that you may need to rummage for some machine screws because the factory screws stripped when I removed them. The oven must have annealed them.

First time was very difficult I tried to make the panel fit into the frame. Broke both side pieces of the trim.Even thouth I broke the trim PartSelect replaced them. I did not expect that.Second time it was easy. Remove the handle first and then the panel slides into the top and bottom only. It does not slide into the side of the frame but sits on top of it. Thanks, Allen

Used new differant screws to mount it and cut and spliced the wires to use the org. Plug.

Replaced trim kit found on site. Everything went well. No real problems. I will book mark your site for the any other parts I may need.

Remember how you remove the glass. The side brackets go under the glass.

Moved oven away from wall, Turned off gas and unplugged electrical from wall. The igniter has a coupler plug that you have to unplug from behind the unit. Take out the bottom drawer. Remove the 2 nuts holding the igniter in place. Remove old igniter. Replace with the new igniter, screw in nuts and thread connector wire to back of unit. Reconnect the igniter behind the unit. Turn on gas and plug in electricity. I checked to make sure it worked before pushing it back into place. I also took time to clean up while the oven was pulled out so it took about an hour - 15 minutes to replace the part - 45 to clean up. Works and looks just like a new oven range!

Excellent delivery.

Removed a cover plate on the back of the stove. Unplugged the old igniter. Pulled the bottom drawer out. Reached in under the stove and undid the 2 screws holding the igniter in place. Screwed the new igniter in and put everything back together. The only tricky bit was reaching the igniter through the bottom drawer opening.

I broke the old trim when cleaning. New trim kit went together great. No screws needed because of new design. Best tip I can give is that the side trim pieces around the oven door go behind the glass on the door not in front of the glass. Visual instructions would be great.

Ordered parts that I thought were correct. BUT I ordered from the door parts... which gave me the wrong screw and unnecessary shims. What I really needed was the cabinet parts! At the time of doing the order, I could not find the owner manual... but found it before the parts arrived. That is what saved me and also thanks to me, for being a pack rat and my grandson finding the spacer on floor after it came out. That made it possible to fix the door. The screw I tried to install, but soon realized it was wrong. I went thru the pack rat stash and found the screw that fell out late last year.....! I then noticed the screw holding the hinge bracket was loose, now that is almost impossible to tighten because everything or tools that I owned were tooooo long (it's only 1 1/2" off the floor)! I tightened that and put the spacer and bottom hinge pin in. The screw was only 3/4" off the floor and difficult to get into the hole without a mirror on the floor under the spot. I finally used a clamp wrench to hold the screw and thread the screw into the hole. From there, most sockets are too long, so I did find a short socket. Now that still took me to the mirror, so I used the clamp wrench to hold the socket to tighten the screw. Thank goodness I am mechanically inclined and can look at a schematic to to understand how something works or I would have had to call for a mechanic. Also I should say ... FIND you manual before ordering to start with the right parts! Manual showed the parts of the cabinet and the door as one long picture, which helped with the repair and would have for ordering.

I shut off the gas and removed the back plate and disconnected the wires. Then I unscrewed two screws from the igniter and replaced the old with the new. Then I snapped the wires together and put the back plate back on. The oven works great!

I pulled the stove out from the wall & took the back lower right cover off. Unplugged the power cord & disconnected the igniter from the power. Took shelves & bottom cover (took two screws out)from oven. Used nutdriver to remove old igniter, then pulled the connector through into the oven, discard. Put new igniter in place with nutdriver.Push connecting cord through to back of stove.Replace bottom cover & shelves. Plug cords together & plug cord back in to outlet.Turn stove on & igniter works!!! Push stove back into place & bake a cake! :)

Opened lower door of stove located ignitor removed 2 small screws that secure part, took guard off back of stove unplugged wire connector removed part plugged new ignitor in re-installed guard, re-installed 2 screws that secure ignitor. Turned stove on oven lit problem solved. This is the 3rd time i have used instant repairman on parts select to fix 3 different applicances and have saved hundreds of dollars fixing it myself with the help of parts select.