FEP310EN0 Roper Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kimberly from Palestine, TX
- Parts Used:
- WPW10308477
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lower element went out
I removed the two screws that held the element in place . I think pulled out the element and disconnected the two wires. I put the new element in and connected the two wires. I went to put the element back in and something sparked and burned up the wire. Lesson learned - turn the electricity off first. I had to pay a repair man to come out and replace the wire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from Fayetteville, AR
- Parts Used:
- WP9761346, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Heating element bent, drip bowl corroded
I just put the drip bowl in and plugged in the new heating element and I was done. It heats much faster and is level now so cooking is much easier. Also the parts arrived sooner than I expected, so I was very satisfied overall. Couldn't have been much easier all around. I will use Partselect.com in the future. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from Newnan, GA
- Parts Used:
- W10355051
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
Baked on sauce
Used cooktop creme, oven cleaner and Mr. Clean sponges. After many days of working on the surface, we were able to remove 99% of the sauce.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steven from SEDRO WOOLLEY, WA
- Parts Used:
- W10856603
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broiler element failed
Slide range out,unplug range,remove rear cover to unplug element wires, open door remove screws inside oven remove element
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry D from Spring Valley, CA
- Parts Used:
- WPW10308477
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Heating element burned up
It was simple. Unscrewed to screws at the back of the oven. Slipped off the wire connectors then attached the wire connectors to the new part, put the screws back in and we were back in business.
Was this instruction helpful to you?
Thank you for voting!
Burner would randomly overheat on any setting (Bad Control Switch)
1) Unplug stove.
2) Remove back cover of the stove held in place by 8 screws (4 short ones for the upper holes and 4 longer ones for the lower holes.).
3) Remove the knob from the switch that you are replacing to expose
the switch mounting screws (2 screws).
4) Remove the screws.
5) Go to the rear of the stove and extract the defective switch.
6) You will see 2 plastic plugs going into/onto the switch. Remove the
plugs. MAKE SURE YOU ARE UNPLUGGED FROM THE
Wall OUTLET!! A small flat blade may be needed to separate the
plugs from switch.
7) Attach the plugs to the new switch (there is only one way to do it.
you wont get them confused and put on wrong.
8) Put the new switch where the defective one was.
9) Come to the front of the stove and put your two screws in and
replace the knob.
10) Replace the back cover,
11) Plug in and test burner.
2) Remove back cover of the stove held in place by 8 screws (4 short ones for the upper holes and 4 longer ones for the lower holes.).
3) Remove the knob from the switch that you are replacing to expose
the switch mounting screws (2 screws).
4) Remove the screws.
5) Go to the rear of the stove and extract the defective switch.
6) You will see 2 plastic plugs going into/onto the switch. Remove the
plugs. MAKE SURE YOU ARE UNPLUGGED FROM THE
Wall OUTLET!! A small flat blade may be needed to separate the
plugs from switch.
7) Attach the plugs to the new switch (there is only one way to do it.
you wont get them confused and put on wrong.
8) Put the new switch where the defective one was.
9) Come to the front of the stove and put your two screws in and
replace the knob.
10) Replace the back cover,
11) Plug in and test burner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Reginald from PLAINFIELD, IN
- Parts Used:
- WP3148953
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The 8-inch burner only heated on high regardless of the temperature setting dialed in.
Unplugged stove from electrical outlet. Pulled temperature control dial off by hand. Remove screws to top back stove panel with Phillips screwdriver. Removed top stove back panel. Unscrewed broken infinity switch from stove. Unclipped wiring harness to broken switch by prying loose with flat head screw driver. Reclipped wiring harness to new switch. Screwed replacement switch back onto stove. Reattached back panel with screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT E. from GLENDALE, CA
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Replace aged Drip bowls
Lift and remove heat elements
Lift and remove Drip bowls
Replace Drip bowls and heat elements
Lift and remove Drip bowls
Replace Drip bowls and heat elements
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Saint Michael, MN
- Parts Used:
- WP3195546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom drawer
It was easy to find the part. I ordered it on Sunday and it arrived Wednesday. A stress-free experience.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Mariposa, CA
- Parts Used:
- WP3188987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken Switch
Made sure was off, Removed rear panel, removed 2 screws, removed wire clips from old switch, installed wires on new switch, installed switch with 2 screws, re-installed back panel, reconnected power and checked switch function. OK!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amanda from Midwest City, OK
- Parts Used:
- WPW10308477
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The heating coil was no longer working.
My husband pulled the oven out and unscrewed the screws(in the back) the heating element came right out. He did everything on his own. The only thing he needed a little help with was for me to keep the heating coil flush to the back wall of the oven, while he screwed the new one in. It was a very quick job. The longest part was pulling the oven out to get behind it and sliding it back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jean-Claude from Miami, FL
- Parts Used:
- WPW10308477
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bake element was taking time to warm up
Wire connection was damaged, replaced end piece
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elaine from BROAD BROOK, CT
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Generic drip bowls in the stores did not fit
Very easy remove the burner and instill the drip bowls
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dana from Black Mountain, NC
- Parts Used:
- WP8203546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Loose terminal caused block to overheat and break
Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- christopher from harrisburg, NC
- Parts Used:
- WPW10308477
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
element went out on the stove
My wife did it! I got home one night and my wife had done it! That's how easy it was! Trust me, he is no handyman (woman) but she did it by herself. The part came fast, the price was better than any one else's
Was this instruction helpful to you?
Thank you for voting!