FGP337GQ5 Roper Range - Instructions

Unsrewed what was left of the trim and oven handle. Just 4 screws total, then replaced the 2 screws of the trim and the 2 screws on handle.
Finished! Replacement parts fit perfect!!! Thanks a milliion!

Removed two screws holding the bottom in, pulled out old bottom, inserted new bottom, replaced screws and tightened them. Total time less than five minutes.

simple change out - remove old grates, install new ones - note that this site/store is excellent

Removed two screws and the front of the door popped off. Replaced the bottom metal piece that the glass front slides into. It was a piece of cake.

Our existing gas stove burner igniter had broken on one of the four burners. I therefore obtained a replacement igniter and mounting screw form PartSelect.com which were indeed perfect replacement parts. However, I could not remove the burner plates from the top of the stove since they were basically welded into position by years of heat. I therefore followed instructions as submitted by a previous customer (thank you Michael of Bloomington, Il), snapped open the stove lid retainer clips, and then lifted the stove surface about 4 inches. Through that opening I was able to reach the underside of the involved burner. Unfortunately, I could not unscrew the existing broken igniter mounting screw and therefore had to break off the already broken igniter and grind down the remaining mounting screw using a drill grinder since the screw was basically welded into place. Once I did that, I was then able to install the new igniter using a separate unused screw hole already in place right beside the old previous mounting screw. With that done, the new igniter works perfectly and the burner works just like new. It was however a lengthy process over two hours long because of the glitches described above. Nevertheless I'm very pleased that the parts were perfect and the repair is complete.

I didn't do it, but I suggest putting down newspaper to keep from having to clean up all the charred remains that will inevitably fall from the parts you have to remove. First, unplug the thing so you don't shock yourself. I removed all the racks for easy access to the drip pan, which had to be removed by unscrewing two screws. Then there was a cover over the flame area that also required two screws being removed. The coil had two screws connecting it, but first I had to pull out the drawer at the bottom, crawl under the unit and unplug the coil. I removed the two screws from the old coil and replaced it with the new one, but first I had to get back under and plug in the new coil. I was unprepared for the virtual small animals that were under the stove, so I took some time to clean out that mess. I tested the thing to make sure it would work, and it did. I put all the pieces back in reverse order and had some really good baked chicken for dinner. I also recommend using gloves, as all the soot is hell on your nice manicure.

removed door handle screws then removed glass retaining tabs from sides put clips on sides of glass held insuation in place and replaced glass replaced door handle replaced two door screws trial opened and closed door successful done

Igniter is in the back bottom of the oven. I had to take off the top of the broiler compartment which has 3 screws. Unplugged the igniter which has two small screws and used a magnetic nut driver. installed the new one. It took 30-45 minutes.

I basically followed the video. The hardest part of the repair was trying to squeeze behind the oven to remove the back plate. Also the original screws holding the igniter took a small Allen wrench that I didn't have so I used an adjustable wrench. One screw was a little difficult but eventually got it tightened. Otherwise this was an easy repair like other reviewers have said.

Replaced bottom trim included in kit.
Installed side door trim.
While trying to slide glass front in place both plastic side trims broke.
Had to use already broken door trim and glued in. Just hope when use oven glue doesn’t melt and will have to replace entire oven.

the research and diagnosis took much longer than the repair on this model. if i had the new igniter on hand, it would have been only about 15 mins.

I still don't have it back together! The first time we ordered the part the gentleman sent me the trim for the left side which seemed to be fine but while replacing it the old part (right side) broke. Ok. so I called to order same part but for the right side. Well, the lady told me I could only order the oven door trim kit, which seems to be too large. I don't think she understood me. Why the 1st time ordering I could get the left side only now when ordering the right side she says we don't sell it that way. Very confused and still can't use my oven since Dec,19th!!

So....the oven stopped working.
I called a local appliance guy and set up an appointment to repair.
$90 to travel here.
$50 for the part
$ labor was about $75
..then tax.
BUT then....I had a moment of clarity.
A new Oven/Range/Stove top was about $400.
This guy was over $200 to repair a 4-7 yr old stove.
So I ordered the part.
A resus monkey could have fixed the stove...I really mean it...Easy is an under-statement.
I found a tutorial on you tube (how to change an Igniter.
Literally 6 screws and unplug the igniter and install the new igniter.
Replace the screws and replug in the unit.

and that's that.

Turn gas off at tank. Oven rack out. 2 screws out of flame spreader and remove. 2screws from ignitor. Pull oven out from location to access rear bottom cover. 2 screws out and unplug ignitor. Guess what ? Reverse order. Not worth paying gas company over 250 dollars.

I just removed the bottom panel in oven and the igniter was right where the flames should be and I removed the two screws and replaced with new part. I replaced bottom oven panel. You need to remove rear panel and plug wire and replace rear panel. My problem was solve. It took 20-30 minutes tops.