FGP335GN0 Roper Range - Instructions

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Moved oven away from wall, Turned off gas and unplugged electrical from wall. The igniter has a coupler plug that you have to unplug from behind the unit. Take out the bottom drawer. Remove the 2 nuts holding the igniter in place. Remove old igniter. Replace with the new igniter, screw in nuts and thread connector wire to back of unit. Reconnect the igniter behind the unit. Turn on gas and plug in electricity. I checked to make sure it worked before pushing it back into place. I also took time to clean up while the oven was pulled out so it took about an hour - 15 minutes to replace the part - 45 to clean up. Works and looks just like a new oven range!

Excellent delivery.

Used new differant screws to mount it and cut and spliced the wires to use the org. Plug.

Replaced trim kit found on site. Everything went well. No real problems. I will book mark your site for the any other parts I may need.

The kit was not supposed to fit my particular model but I felt the picture was exact and took a chance and had it sent. It was a perfect fit and was easy to assemble and looks like a new stove. I paid one third of the cost estimates that I got from local appliance centers and even other on line sites. I'm very please with the product and the delivery was more than prompt!! I couldn't believe the service!!! Thanks!!

most difficult part was having to pull the stove out to access the Igniter wire connector. unplugged connector, removed 2 Igniter mounting screws, installed new Igniter and connected plug. very easy project. less than 30 minutes total thanks to website for perfect diagnosis of problem

I shut off the gas and removed the back plate and disconnected the wires. Then I unscrewed two screws from the igniter and replaced the old with the new. Then I snapped the wires together and put the back plate back on. The oven works great!

Since the broiler worked fine, I took the igniter from the broiler (exact same) and moved it to the bottom and sure enough oven ignited fine. I did this to isolate the problem, because it could have been either the igniter or the valve. I put the broiler igniter back on top when I got the new part, because it is used only 5% of the time. Be aware that you may need to rummage for some machine screws because the factory screws stripped when I removed them. The oven must have annealed them.

I pulled the stove out from the wall & took the back lower right cover off. Unplugged the power cord & disconnected the igniter from the power. Took shelves & bottom cover (took two screws out)from oven. Used nutdriver to remove old igniter, then pulled the connector through into the oven, discard. Put new igniter in place with nutdriver.Push connecting cord through to back of stove.Replace bottom cover & shelves. Plug cords together & plug cord back in to outlet.Turn stove on & igniter works!!! Push stove back into place & bake a cake! :)

To begin with,the symptoms were strange.....the burner would not ignite even though the igniter was glowing....but if you bumped anything in the broiler or pulled the drawer out and closed it abruptly,it would lite. This went on for a few weeks , until slamming and banging worked no more.(that was getting old anyway)I went ahead and ordered the igniter.It came fast and was very easy to replace.I went in from the oven,took out the racks and the bottom plate(2 screws), exposing the flame diverter that is just above the burner.(2 screws)You can access the igniter now ,and remove it.(2 screws),and unplug it.Reverse order to install the new one.I didnt unplug the range or turn off the power,because I screwed the igniter on first and then it was a matter of just plugging it in. Everything went back together and turned on the oven. Worked fine. Very easy to do,and no more banging around the broiler.Should have done it sooner.

Opened lower door of stove located ignitor removed 2 small screws that secure part, took guard off back of stove unplugged wire connector removed part plugged new ignitor in re-installed guard, re-installed 2 screws that secure ignitor. Turned stove on oven lit problem solved. This is the 3rd time i have used instant repairman on parts select to fix 3 different applicances and have saved hundreds of dollars fixing it myself with the help of parts select.

I removed the oven racks, removed the oven floor and the oven burner cover, pulled the range out and removed the small panel on the back which covers the igniter connector. I disconnected the old igniter, removed the two screws holding the igniter in place and removed the old igniter from the oven. Then screwed on the new igniter, fed the wire through to the back and connected the new igniter. Turned on the oven and voila' we have ingnition! The oven is working again but I'm getting the "F2" routine sometimes. It doesn't do it every time but when it does I unplug and replug and then it works. I'm a 67 year old female and I considered it very easy so pretty much anyone should be able to do this repair.

ordered the part and in less then 24 hours from ordering the part it was shipped and delivered and my husband and I put the part in took us no time at all very easy to do... 2 years ago i had this same problem and called a guy in the area cost me $200. I had dinner in the oven by 5 that night!!!!

Removed bottom plate by pulling up from the back (had some resitance), Two machine screws holding cover over igniter, used 3/8" socket to remove. Pulled oven from wall to disconnect igniter @ coupler, unscrew one more machine screw, fed replacement igniter into slot and coupled, attached single screw to pipe, put cover w/ 2 machine screws on top, install bottom plate. Had to use butter knife to get bottom plate to fit into the front cabinet area of stove. Done & working fine.