FES364BL1 Roper Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Vicki from Prospect, CT
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The baking element burned out, where actual sparks and flames were flying.
We have had our Whirlpool oven for 22 years and became very concerned that a part would not be available. We were thrilled to find the part as well as install the new part ourselves. With a screw driver, we disconnected the old baking element ( be sure to shut the power while doing this) and screwed in the new one. That simple!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from lexington, OH
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
low heat bottom element had cracked
simply removed screws & old part.., replcd new part & screwed back into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Lewisburg, WV
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Baking element burnt out
Turned off the breaker to the stove. Removed the two screws holding the element in place. Pulled off the wire terminals, removed old element. Reconnected the two wires, slid new element into place, reinserted the two holding screws, turned back on breaker. 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from UPPER MARLBORO, MD
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The old bake element had burned out
It was so easy. I removed the baking racks. Then I unscrewed two Philips head screws that held the rack in place. Then I pulled the two connections apart from the wiring. Plugged the new element into the wiring. It was as simple as sliding it in and out, replaced the screws, and within minutes I was back to baking again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- brian from glenelg, MD
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burned out element
unplugged oven unscrewed old element replaced with new one plugged in oven it only took 2 days to get new element saved time and gas
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from Kannapolis, NC
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old bake element burned out
removed old bake element (remove two screws, disconnect two wires. install new element connect wires, replace screws to hold in place. turn on oven to be sure it works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Wichita, KS
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven heating element went out
Backed out two screws, disconnected two wires from faulty element, connected wires to new element, screwed back into place. (New element was ordered by phone and received the next day.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rudolph from Goshen, KY
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bake element burned into
Used screwdriver to unfasten the old element from the oven frame. Then unplugged the two wire plugs from the back of the old element. Reversed the process to install the new. Couldn't have been any simpler.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Adam from Longmont, CO
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The lower bake element did not heat up
First I made sure it was in fact the lower bake element that was broken. I turned the oven on & noted the element did not glow red. I also used a laser thermometer to verify the element was at "room temperature" for the room it was in (the oven - about 200 degrees, given what the upper bake element was contributing.)
And close visual inspection showed that a section of te bake element had melted thru where something had recently spilled onto it.
Swapping it out was easy - turn off the electrical breaker controlling the oven, unscrew the bake element, disconnect the electrical contacts to it (which required pliers, since they had been on a Looong time, and a little care to not use the pliers too hard & thus break the wires or contacts), then reverse the process to install the new element.
It works great now.
And close visual inspection showed that a section of te bake element had melted thru where something had recently spilled onto it.
Swapping it out was easy - turn off the electrical breaker controlling the oven, unscrew the bake element, disconnect the electrical contacts to it (which required pliers, since they had been on a Looong time, and a little care to not use the pliers too hard & thus break the wires or contacts), then reverse the process to install the new element.
It works great now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from Bossier City, LA
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element burnt out.
Simply remove two phillips screws, unplug and replug. Thanks to the quality parts I bought here it saved me $65.00 on the part alone. Locally $85.00 plus shipping.
Thanks guys for your help.
Thanks guys for your help.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from Ardmore, PA
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old element burned out
Removed the two sheet metal screws holding the element, Unplugged the contacts and plugged and fastened the new element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Norman L. from Austin, TX
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bake element did not heat to temp selected
removed the old one replaced the new one every thing works like new. THANKS
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brenda from Charlotte, MI
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element quit heating
un plugged oven from wall Unscrewed 2 screws pulled out old heating element and plugged in new heating element then plugged stove back in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Pattonsburg, MO
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Electric Oven burner element burned out.....
Made sure that "Breaker" for oven is in the off positon.
Opened oven door to the first "stay open" position...lifted door straight up...and off of the hinges....which removes the door....and allows easier access to oven.
Removed oven racks
Removed two philips head
Pulled burned out element toward the front of the oven.....exposing the two connector wires.
Used pliers to pull wire connectors from burner element connectors.
Reversed the order of this process....to install new element.
Opened oven door to the first "stay open" position...lifted door straight up...and off of the hinges....which removes the door....and allows easier access to oven.
Removed oven racks
Removed two philips head
Pulled burned out element toward the front of the oven.....exposing the two connector wires.
Used pliers to pull wire connectors from burner element connectors.
Reversed the order of this process....to install new element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from NESHANIC STATION, NJ
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
split element
simple replacement
Was this instruction helpful to you?
Thank you for voting!