FGS337GW0 Roper Range - Instructions

Unscrewed the feet from the floor. Pried up the range top, removed burners. Unscrewed sides of the range from wooden cabinet it was recessed into. Unplugged range from outlet. Pulled range out into the open. Removed back cover. Discovered that I have the wrong replacement part.

Turn gas off at tank. Oven rack out. 2 screws out of flame spreader and remove. 2screws from ignitor. Pull oven out from location to access rear bottom cover. 2 screws out and unplug ignitor. Guess what ? Reverse order. Not worth paying gas company over 250 dollars.

I just removed the bottom panel in oven and the igniter was right where the flames should be and I removed the two screws and replaced with new part. I replaced bottom oven panel. You need to remove rear panel and plug wire and replace rear panel. My problem was solve. It took 20-30 minutes tops.

I use the table knife to slide the side of the stove to open the top. then I traced one of the wire to where it was hooked up and remove it and replaced it. I did them one by one.

This oven probably was manufactured in the '60s when the house was built. The door doesn't just pull off like the newer models. These pins fit into small holes on the oven hinges. I inserted the pins and lifted the door to a 45 degree angle, before pulling the door completely off. Now that turned out to be the easy part. I then proceeded to completely dismantle the door. It actually has 4 glass layers which had to be cleaned individually. The hardest part of all was actually remembering how to put it back together again. I put the door back on just as I had removed it, then took out the pins, and I was finally done! This was not an easy project, BUT the results look great.

took out old oven bottom by removing 2 screws, placed the new oven bottom in place put the screws back in and was done.

just replaced the broken glides with the new ones.

Easy. Slide oven away from wall. Turn gas off and unplug. Open oven door. Remove grates and lift out bottom tray to access igniter. Igniter is affixed to burner tube using (QTY=2) 1/4” bolts. Used socket wrench due to limited space for nut driver handle length. Detach igniter. Got to back of oven and remove the protective plate at the bottom. There are three phillips screws. Verify you have the correct cable for igniter by tugging on igniter in oven. Pull old igniter out. Replace old igniter with new using old bolts! Run igniter cable through back using same hole as old igniter. Plug in connector in the same fashion as prior. Before reassembly, test oven. Plug oven in and turn gas back on. Set oven to bake and set temperature. If igniter lights the gas burner tube, you’re done! Reverse process to put oven back together. Job takes 20 minutes, maximum. Saved a bundle!

Was super easy even I could do it. Wish I would have done it 2 years ago when my husband broke it. Just used a Phillips screwdriver. Very easy!

Only one screwdriver needed for this simple repair. Unfortunately for me it did not repair my oven and a new code on the oven indicated a bigger problem with computer board.
Part Select was great to work with and accepted a return and promptly refunded me for the part.
Thank you!

It was a very simple repair pulled the old ignitor, and installed the new one in under 15 minutes. It was nice that it was a factory original part and matched perfectly. The wiring plug matched so no need to cut the plug and get ceramic wire nuts. The ignitor works perfectly and gets white hot rather than dark orange, the gas ignites in 20 seconds compared to 90 seconds.

Used a nut driver removed 2 bolts from igniter and 1 wire clip in the back looked on website other people had the same problem ordered part received it in 3 days installed new igniter took about 5 minutes to take out and 5 to install the new one now my oven is working great thanks to this site

Took the back off the stove, removed 2 screws, unclipped the bad sensor, clipped the new one on, put the screws back in and the back of the stove back on and that was it - 10 minutes

DISCONNECTED POWER AND GAS TO THE RANGE. REMOVED 6 SCREWS FROM REAR OF THE RANGE. REMOVED THE 2 SCREWS HOLDING THE TEMPERATURE SENSOR IN PLACE. DISCONNECTED THE LEAD FOR THE SENSOR. INSTALLED NEW SENSOR IN REVERSE ORDER. OVEN WORKING PROPERLY NOW.

this is the easiest repair possible. take out bottom drawer.. disconnect power cord. igniter is above burner grid.remove the two screws {be careful not to lose them}. move stove out from wall. from behind stove remove three small screws holding tin cover. and unplug the connector..install new igniter from under stove and plug in connector. install tin cover and move stove back in. replace bottom drawer. and plug in power. replacement saved the repair cost or replacement of a new stove..