RME32301 Roper Range - Instructions

It was easy to find the part. I ordered it on Sunday and it arrived Wednesday. A stress-free experience.

1) Unplug stove.
2) Remove back cover of the stove held in place by 8 screws (4 short ones for the upper holes and 4 longer ones for the lower holes.).
3) Remove the knob from the switch that you are replacing to expose
the switch mounting screws (2 screws).
4) Remove the screws.
5) Go to the rear of the stove and extract the defective switch.
6) You will see 2 plastic plugs going into/onto the switch. Remove the
plugs. MAKE SURE YOU ARE UNPLUGGED FROM THE
Wall OUTLET!! A small flat blade may be needed to separate the
plugs from switch.
7) Attach the plugs to the new switch (there is only one way to do it.
you wont get them confused and put on wrong.
8) Put the new switch where the defective one was.
9) Come to the front of the stove and put your two screws in and
replace the knob.
10) Replace the back cover,
11) Plug in and test burner.

Unplugged stove from electrical outlet. Pulled temperature control dial off by hand. Remove screws to top back stove panel with Phillips screwdriver. Removed top stove back panel. Unscrewed broken infinity switch from stove. Unclipped wiring harness to broken switch by prying loose with flat head screw driver. Reclipped wiring harness to new switch. Screwed replacement switch back onto stove. Reattached back panel with screws.

My husband pulled the oven out and unscrewed the screws(in the back) the heating element came right out. He did everything on his own. The only thing he needed a little help with was for me to keep the heating coil flush to the back wall of the oven, while he screwed the new one in. It was a very quick job. The longest part was pulling the oven out to get behind it and sliding it back in.

Wire connection was damaged, replaced end piece

Made sure was off, Removed rear panel, removed 2 screws, removed wire clips from old switch, installed wires on new switch, installed switch with 2 screws, re-installed back panel, reconnected power and checked switch function. OK!

My wife did it! I got home one night and my wife had done it! That's how easy it was! Trust me, he is no handyman (woman) but she did it by herself. The part came fast, the price was better than any one else's

Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

took the handle off, replaces the side trim piece and replaced the handle. Very simple!

Ordered both parts using the excellent breakdown illustrations of the door. Received the parts along with video instructions on how to repair.

I didn't. Don't know how to get to light bulb to change it for this specific model

It went great. I am not very handy, but with a little help from your website reviews, I was able to easily remove the old broiler element and replace it with the new one in less than an hour. I immediately tested it and found that it worked great.

Unscrewed the switches and let the switch hang while replacing one wire at a time. Followed instructions on wire replacement. Exact parts, only shaft on 6" switch was too long -- okay, because it is designed to break off a piece on end of shaft, then the knob fit. Everything was perfect.

Removed back plate, replaced infinite switch.
Replaced receptacle holder. Took a moment to see how to install wires into the receptacle, no instructions on orientation of wires into the receptacle. Wired receptacle per instructions. Placed receptacle into holder and installed burner. Burner Burner would not lay flat, receptacle longer than original. Removed receptacle from holder, plugged in burner and placed burner into position.

1993 model oven, built in wall model, so didn't to remove oven for the normal rear access to replace the lamp socket. As someone else posted, replacement can be done from inside the oven -- BUT the socket removal was more complex than just 'twisting it out.' But below worked! (1) Turned off oven power at circuit breaker panel. To facilitate working in the oven compartment, removed oven door (2 screws on back of door), raised the over door almost closed, put 2 large nails through the hinge holes when they lined up. Lifted the door out (heavy ~20-25 lbs) and put aside. (2) Put work light inside oven. (3) unscrew glass socket lens and the bulb). (3) Using inspection mirror, studied the inside of the socket to determine that its lock tab type and locations -> were on left and right sides of the socket. These tabs needed to be bent in, but they were each held out by a small circumferential length of think metal, a tab about 3/16" x 3/8". These small tabs could be moved/positioned by just finger friction, with a little start with a screwdriver tip on their edge! I got an end positioned to put sharp screwdriver under that end, then pried it (bent it) inward a short distance. Enough to use needle-nosed pliers to pull it completely out - came fairly easily. Repeated on other side of socket. (4) Then, with pliers, bent each of the 4 locking tabs inward a short distance, Used sharp tool to get one socket edge lifted a small amount; then use mini-pry bar and screwdriver to gently pry around the socket in steps, working evenly around its edge. At about 3/8", it was free. Lifted it inward gently so as not to damage the insulation of the 2 wires attached to its rear. Noted the direction of the wire tabs was straight up (keep same orientation on new socket). (5) Needle-nosed pliers on each connector to gently work the connectors off their socket tabs. Note one tab is larger than the other. Keep the wires inside the oven compartment. Don't damage the insulation. (6) Pushed the wire connectors onto their respective new socket tabs. Aligned socket with the tabs upward, and inserted it, careful to nurse the wires back into the oven wall hole; press socket into the hole, pushing it in evenly and firmly until flush. (7) Pushed in the new type bulb that came with new Socket. Turned on power, and light came on. (8) screwed on new glass cover. (9) Lifted oven back onto the hinge prongs. (easier with two people to get the prongs aligned and into their door slots.) Worked door left and right to get it to lower down fully. Removed nails, lowered door, and put its 2 screws back on. (10) Poured a glass of wine.