FES355TQ1 Roper Range - Instructions

Moved the stove out from the wall. Took out the screws from the back and then from the top. I pulled the piece through the back to unplug the clips from the elements. But the wires went back through the openings. So I had to take the back off of the stove to get to the wires to put back through the holes in the stove. Once the clips were back together, I put the back back on the stove. Rebolted the part to the stove and moved it back.

Removed the screws that hold the handle to the oven door. In less than 5 min had the glass in place and you couldn't even tell that I had broken the glass door.
super easy to change very helpful company to get stuff from.

Very easy . Just removed four screws and removed the back cover. Then just unplugged two clips from the element . The repeated all of my steps in reverse . Be sure to unplug the oven before you start on the project .

Since it fell out, we didn't know how to put it back in--after several hours of frustration, thinking the glass was too big--we went to appliance store and looked at a stove and found out the glass went on the outside with only a groove and handle holding it in place. After that, it took about 30 minutes to complete.

I removed the two screws that held the element in place . I think pulled out the element and disconnected the two wires. I put the new element in and connected the two wires. I went to put the element back in and something sparked and burned up the wire. Lesson learned - turn the electricity off first. I had to pay a repair man to come out and replace the wire.

I turned off the breaker (I'm a little nervous even unplugging a 220 plug). I first removed the cover from the back of the stove to get to the wiring/socket. Removed the two wires from the leads - they just pull off by hand but use a needlenose pilers if it is stuck. One is larger so no need to try to remember which one goes where. I removed the glass cover and bulb from inside the oven. I read another post on this site that said there were clips that you had to press to get the old socket out which helped. That part was a little tricky as the insulation around the socket makes it hard to see and the opening is really tight. I finally found the clips and pressed one then got that side out enough to hold the clip back then pressed the other clip and I was able to push it right out. I did not have the strength to press both clips with enough pressure but if you do, that would probably be easier. From inside the oven, I pushed the new socket through the hole - there was a little notch in the opening that had to match up with the socket. I had to push pretty firmly until I felt both clips snap in place. Replaced the wires, turned on the power, screwed in the bulb and cover and I had light!

I discoverd my switch box locked with my stove electrical port and stove stopped functioning. Pulled my stove back and saw that the "terminal block" was melted on one side; hence, switch box locked in place to avoid a fire, thank goodness. Looked up part on internet, unplugged stove, took off terminal box, ordered part and replaced. BTW - PART SELECT is awesome; I received my part the very next day!!! :-) Very happy with their service.

Part came super fast, remove and replace two screws - nothing to it

I cut the ends of the cord and went with direct wire (no round eye clip) to the back side of the terminal block and tightened firmly. It took about 20 Minutes.

Unplugged the range.
Removed the screws holding the flat top from the front bottom (inside doorway)
Unplugged the two connects at the back and removed the ground screw.
Unscrewed the bar holding the elements and remove the element.
Replaced with new element. Installation is reverse of removal.
Very easy if you are careful..Always unplug your appliance before working on it.

Removed oven door and the 3 screws holding the bottom door trim. Attached new trim piece and reinstalled oven door. Entire job took less than 5 minutes.

took back of stove off ,total 6 screws, unpluged blown computer 3 plugs, pluged in new!

After removing the back of the stove, the old light socket was fairly easy to remove. The new socket slipped in place and the wires reattached and now the oven has a light again. A very simple process--especially for someone who's not an expert in repairing appliances.

Slide range out,unplug range,remove rear cover to unplug element wires, open door remove screws inside oven remove element

I simply put the control knobs on the shaft and
they worked great. I love them. Thank you.