Models > N9157X0 > Instructions

N9157X0 Roper Range - Instructions

Jump to:

All Instructions for the N9157X0
61 - 75 of 116
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Janet from Ada, MI
Parts Used:
8009
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
light bulb went out in my oven
My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.
2 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Brian from Westport, CT
Parts Used:
WPY04100165
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
intermittent heat from burner
Pulled out electric heating element and replaced with new. I have had this frustrating problem for 2 years and after replacing the elements they now work like new! My only question, why did it take me so long to replace???
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Shirley from Las Vegas, NV
Parts Used:
8009
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Light burned out in upper oven
Screwed in light bulb and glass protector
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
peggy ann from forest city, NC
Parts Used:
8009
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
replaced oven lightbulb
very easy
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from Toledo, OH
Parts Used:
330031
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Burner Would Not Heat
One screw taken out, 2 wires switched, new part & screw put in. Burner like new!
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gudrun from Santa Fe, NM
Parts Used:
W10196405RW
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
replacement of drip bowll
take the old one out, but the new one in.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from Schwenksville, PA
Parts Used:
8009
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
oven light burnt out
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
3 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from Phillipsburg, NJ
Parts Used:
330031
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Wire broken off plug in block
Removed old block , cut off wires , used new wire nuts, heat shrink , supplied with parts , job done lowered range top went fishing ...
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
john from reading, MA
Parts Used:
330031
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
contacts had gotten burnt out/blackened with age so burner was intermittent.
lifted the cover, unscrewed the ceramic wire fastners, put the new part in, and voila, job done and working perfectly
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Greg from Versailles, IN
Parts Used:
330031
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
large burners not working
Read instuctions first Turn breaker off to stove or unplug to be sure. Remove burner and drip pans. Remove scews holding socket in place if you are doing more than one make sure you keep in same location. Raise cook top untill supports latch in. Assemble plug it comes with two types holder compare to your plug. cut wire to old plug so you have enough wire to connect back with new. Strip wire back and place shrink tubeover wires wire nut together heat with a lighter or heat gun then do remaining plugges. place back in cover and replace scews. make sure wire are not to long to get under burner when cook top lowered. Lower cook top and clean burner plug ends with a little sandpaper to make sure they make good connection. replace pans and burner. turn on breaker or plug in stove making sure the burners come on when turned on good luck g.d.
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
dicky from mcrae, AR
Parts Used:
330031
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
replace burner coil connector
Cut the two wires approx 1 inch behind old connector and removed one screws to remove old connector, stripped approx 3/4 inch off the wires and connected them to the new wires on the new connector with wire caps and shrink wraps which came with the new connector. Replaced the old screw with the new screw and the job was completed. Be sure and disconnect power before starting!!
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Judith from Phoenix, AZ
Parts Used:
8009
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Bulb Replacement
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gail M from Lockport, NY
Parts Used:
330031
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Burner was slow heating at times. Moved back burner to front still same thing.
Unscrewed screw holding bracket. Used side cutters to cut wires. Replaced the bracket, put the shrink wrap on wires, twisted wires together and held with wire caps. Shrunk the wrap with lighter. I'm a 67 year old female.. No problems.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from Springfield, VT
Parts Used:
WP3147132
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
prongs for the wiring corroded underneath solid element
Very straight forward. Uninstalled the old corroded element by unscrewing bolt and snipped the wires that were attached. By knowing how the element came out, I was able to install the new element very easily. Just slide the wires into the holes attached to the prongs and tighten down the screw. Very easy and worked right away. My Magic Chef electric range has to be at least thirty years old. Very happy PartSelect had the right part.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Earl from Union Mills, NC
Parts Used:
330031
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
burner would not heat up the connection was bad
loosened the screw holding the block pulled it out toget to wire cut it about 4 inches long followed the inst.with block kit and it was a breeze. burner working fine now should have did it sooner.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the N9157X0
61 - 75 of 116