FES340VL0 Roper Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Derek from Gilford, NH
- Parts Used:
- WP77001094
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Baking element overheated and split into two parts.
First removed 2 screws holding in element housing at the back of the oven. Pulled element out and disconnected wire leads from the the element connection points. Reconnected leads from new element, pushed back into the back of oven and rescrewed into the oven housing. Done, very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Noah from Richardson, TX
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
corroded, rusted drip bowls
replace
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Desoto, MO
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
two of the burners were working intermittently
I shut off the breaker checked for power then cut old plugs making sure to allow a little slack. Tightened down wire nuts put on a couple wraps of electrical tape and that was it. Burners work great now I would reccomend this product to anyone with a similar problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from Weston, WI
- Parts Used:
- WP77001094
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
oven coil burned out
by myself
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Montgomery, AL
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Top element not heating
Ordered wrong part at first caused me to blow out two elements. With the help of PartSelect I was able to get the right surface block terminal and replaced both of them, then found out I had a bad switch, they got the switch within 2 days I had my stove working good again. Thanks to PartSelect. Also watched the video which was very helpful ML
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gail M from Lockport, NY
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner was slow heating at times. Moved back burner to front still same thing.
Unscrewed screw holding bracket. Used side cutters to cut wires. Replaced the bracket, put the shrink wrap on wires, twisted wires together and held with wire caps. Shrunk the wrap with lighter. I'm a 67 year old female.. No problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from South Fork, CO
- Parts Used:
- WPY0063532
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Oven lower element
Description of the element indicated that it would work for the oven burner. However, it obviously was meant for the broiler element. I had to remove the thin metal piece with the attachment holes in it (the holes didn't match the holes in the back of the oven). To install I had to drill two holes in the remaining attachment flange to match the holes on the back of the oven. Then I made three metal supports out of sheet metal to hold the element up approximately 1 1/2" off of the bottom of the oven. Just thankful to find one that I could make work. Oven works fine now. LF
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Madison, WI
- Parts Used:
- WP77001094
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven heating element burnt out
The repair was simple, two screws and plug in and it was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from Union Mills, NC
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burner would not heat up the connection was bad
loosened the screw holding the block pulled it out toget to wire cut it about 4 inches long followed the inst.with block kit and it was a breeze. burner working fine now should have did it sooner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gene from kent, WA
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burner not working
burner was shorting out replaced part works great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Suffield, CT
- Parts Used:
- WP77001094
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
no heat from bottom element
1. waited unsuccessfully for heat (one hour) 2. realized the bottom element wasn't working (one minute) 3. found part on-line from pictures (five minutes) 4. ordered part (one minute) 5. received part (36 hours) 6. installed part (five minutes) 7. "THAT'S how you fix the oven" look to husband (1-2 years)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kyle from Schwenksville, PA
- Parts Used:
- W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
rusted drip bowl
remove burner by hand and remove old drip bowl replace with new bowl inspect burner for ware and insert back into slot.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ann from Memphis, TN
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Drip Bowl beyond cleaning
Removed old bowl and dropped in new one!!It looks great - the cooktop is probably 30 years old.Your serviceperson was courteous friendly and very rapid.This actually is the second replacement but I was pleasantly surprised that the part was available. Thanks!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robin from Boca Raton, FL
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Two drip Bowls needed to be replaced
No tools needed. And it's always great to be able to replace parts on my VERY old counter-top range. It still works very well, and now it also looks great. Delivery was amazingly fast, too! Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Boyd from kalamazoo, MI
- Parts Used:
- 330031
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Burners did not get hot or went on and off
After carefully inspecting existing burner receptacles, I unscrewed them, raised and propped stove top. Determined which bracket to use from new kit and proceeded to cut and strip wires, twist ends together with supplied ceramic caps and heated shrink wrap on that junction. Works great. BTW got parts in 2 days in great shape and good directions.
Was this instruction helpful to you?
Thank you for voting!