FES340VX0 Roper Range - Instructions

removed the screws disconnected the old one and connected the new one and put the screws back on it

I took a couple of screws out that hold the bottom
element in place replaced the old one with the new one and fired it up. Worked like a charm and maybe this old stove will live on to make more Roast beef dinners.
If it been any easier my 10 year old grandson could have done it.

Repair? What repair? I just removed the old drip bowl and replaced it with the new one. Piece of cake.

lifted the cover, unscrewed the ceramic wire fastners, put the new part in, and voila, job done and working perfectly

I ordered the new part, which arrived in just 2 days. I did not pull the oven away from the wall, I merely turned off the electric, unscrewed the bad element, pulled it out enough to see the ends, and then I removed the existing wires using needle nose pliers. I put the wires on the new element, inserted it back into the oven wall, and screwed it tight. I turned the electric back on, and checked it out. Worked like a charm! Only 40 bucks (including shipping), five minutes of my time, and I avoided an expensive service call. :-)

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, connected the new wires, replaced the two screws and turned on the oven to test it. Easiest repair job I have ever done.

Removed old block , cut off wires , used new wire nuts, heat shrink , supplied with parts , job done lowered range top went fishing ...

Removed 2 phillips screws and pulled elements out 3 to 4 inches. One of the leads touched the housing and blew the circuit breaker, so don't forget to unplug or turn the breaker off! Simply slide clips off and install on new element. push back in place and reinstall 2 screws. Very simple.
P.S. element was delivered very fast!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.

While trying to clean the oven, I decided to remove the lower heating element to make it easier. After removing the 2 screws on the bracket that holds the heating element in place, I pulled the heating element out only to short it out on the back of the oven and wreck the element. Luckly I was not injured or shocked, so if you need to do this, I recommend reading the owner's manual on how to property ground out the circuit first.

Anyways, to replace it, I just removed the lower panel on the back of the oven (roughly 10 screws). Installed the new element on the inside of the oven and screwed it into place. Then, connected the wires to the element from the back of the oven. Replaced the panel and turned the power back on.

In all, it took probably 15-20 minutes to fix and only cost me $37. I know that a minimum repair cost for this from Sears would have been $150, so definitely worth my time.

I had bought the 1st set of plug-in blocks at lowes, They were the only type they had the univeral ones! They did not hold the elements plug tight enough and half the time they would have to be punshed in more then they would snap and sizzle- I ordere the newer style and they have done great they are better made and heavier metal parts- they elements fit in snuggly and do not sizzle or nor do I have to push the element in. This stove is 35 years old and I have replaced most everything on it. But it's still cooking...

Read instuctions first Turn breaker off to stove or unplug to be sure. Remove burner and drip pans. Remove scews holding socket in place if you are doing more than one make sure you keep in same location. Raise cook top untill supports latch in. Assemble plug it comes with two types holder compare to your plug. cut wire to old plug so you have enough wire to connect back with new. Strip wire back and place shrink tubeover wires wire nut together heat with a lighter or heat gun then do remaining plugges. place back in cover and replace scews. make sure wire are not to long to get under burner when cook top lowered. Lower cook top and clean burner plug ends with a little sandpaper to make sure they make good connection. replace pans and burner. turn on breaker or plug in stove making sure the burners come on when turned on good luck g.d.

Two screws in the oven removed the old part and the wires unplugged from the unit. When the new part came in , it was plug and play. Plugged the wires into the new part, put part into holes in oven and screwed the screws back in place and we were ready to go. The part was here in record time. We ordered it on Sunday, it shipped out on Monday, it arrived on Tuesday and we were back in operation! Thanks for a really smooth repair experience!

Cut the two wires approx 1 inch behind old connector and removed one screws to remove old connector, stripped approx 3/4 inch off the wires and connected them to the new wires on the new connector with wire caps and shrink wraps which came with the new connector. Replaced the old screw with the new screw and the job was completed. Be sure and disconnect power before starting!!

shut off circut breaker. un pluged stove removed back panel disconected 2 wires on element. removed 1 screw that holds element in place pull out old element put in new reassemble