2222A1A Roper Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Alison from Carnation, WA
- Parts Used:
- WPW10196405, WPW10196406
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The drip pans needed replacing.
Put in the new drip pan -- which are really nice shiny ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Carnegie, PA
- Parts Used:
- WPW10196405, WPW10196406
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dirty drip bowls
Just remove old bowls from range top and put new ones. That is all ... just super simple! :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Carnegie, PA
- Parts Used:
- WPW10196405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dirty drip bowl
Remove old drip bowl from the range and put a new one back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gail M from Lockport, NY
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner was slow heating at times. Moved back burner to front still same thing.
Unscrewed screw holding bracket. Used side cutters to cut wires. Replaced the bracket, put the shrink wrap on wires, twisted wires together and held with wire caps. Shrunk the wrap with lighter. I'm a 67 year old female.. No problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Brookfield, CT
- Parts Used:
- WP660533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner failure
Removed and replaced burner unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- judy from coarsegold, CA
- Parts Used:
- WP660533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner fell apart
Just plugged it in and away I went.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from Union Mills, NC
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burner would not heat up the connection was bad
loosened the screw holding the block pulled it out toget to wire cut it about 4 inches long followed the inst.with block kit and it was a breeze. burner working fine now should have did it sooner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Florence, KY
- Parts Used:
- 4328405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
toasted heating element
Could not have been easier and I would never call myself a handyman by any stretch. Unscrewed 2 screws pulled the element out of the 2 connectors, plugged the new one back in and put the screws back in and DONE. It took less than 5 minutes and if I can do it anyone can.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gene from kent, WA
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burner not working
burner was shorting out replaced part works great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Addison, TX
- Parts Used:
- W10900107
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Original burner switch fell apart
Replacement was simple. Old switch was easily removed. Once I swapped the wires from old to new we were in business. One thing I would do differently than the included directions called for. I wish I had waited until I had installed the new switch to set the shaft length. I snapped off one too many sections of the shaft after measuring the original shaft as recommended. If I had installed the replacement switch and then set the shaft length it would have been more accurate. Everything still works but one knob is now slightly lower than the other three.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Graham from Bridgeville, CA
- Parts Used:
- W10900107
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
plastic post for knob broke off
I broke the correct post from the new cluster of post selections and stuck it on. I had the kit for a couple of weeks before I realized that this was not an electrical problem. It would have been good of you to send only the new plastic post. That kit was intimidating for a 73 year old woman who lives in the country and does most of her own plumbing and other household repairs. The repair took less that one minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Staunton, IL
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner keep coming on and going off had a short in burner plug-in block.
Turned off stove breaker. Unscrewed burner from stove top, took out burner and spill pan. Lifted top of stove, cut the wire as instructed and put all parts together as instructed. Placed everything back together as instructed. I did it myself!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dallas from Arlington, TX
- Parts Used:
- WPW10196405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I needed to replace to two 8* drip bowls on the kitchen range
(a) I took out (and threw away) two stained 8* chrome drip bowls on my kitchen range; (b) ti put in two new 8" chrome drip bowls on my kitchen range. I'm pleased that I was equal to the task.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Kettering, OH
- Parts Used:
- WPW10196405, WPW10196406
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Stove needed new bowls
Just dropped in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gizella from mays landing, NJ
- Parts Used:
- WPW10196405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old dirty drip pans
Removed heating element, installed new drip pan, replaced heating element. Was amazed at fast delivery - ordered in afternoon, arrived fed ex next morning!
Was this instruction helpful to you?
Thank you for voting!