N3478XRW Norge Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Scott from FORT WORTH, TX
- Parts Used:
- 12400035
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Self tapping screws stripped out, one broke in mounting hole
Punched out broken screw. Drilled out damaged threads to same size as igniter mounting holes. I used nuts, bolts and lock washers to mount igniter. Would have been very easy if mounting screws had come out. Video very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from MEADVILLE, PA
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
OVEN WOULD NOT HEAT
TOOK OVEN BOTTOM APART AND LOSSENED OLD IGNITERTHEN WENT TO BACK OF OVEN TOOK BACK OFF DISCONETED OLD IGNITER PULLED THE NEW THUR AND CONNECTED PUT BACK ON THEN ATTACHED FROM THE FRONT PUT OVEN BACK TOGATHER THEN TURNED OVEN ON IT WORKED I DID IT MYSELF I AM 64 YEAR OLD WOMEN
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Chapell Hill, NC
- Parts Used:
- WPW10162384
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Oven heat loss, door gasket needed replacement
The entire "project" took me less than 3 minutes, and required no tools at all! First, the saleswoman over the phone pointed me to the correct product for my problem ($30 less than what I thought I needed), and it arrived at my home within 4 days. Then, it was just a matter of pulling off the old gasket, and snapping the new one in place! Simple!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Atlanta, GA
- Parts Used:
- 74002312
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broiler drawer didn't track poperly
Remove screw securing the broken drawer guide. Placed new drawer support in place and tightened screw. Replaced drawer. All done in less than 5 minutes (and cheaply).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Merrimac, MA
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Oven burner would periodically go out and re-light
The ignitor is held on by two screws which were rusted in place. When I tried to remove them, the screws became stripped and had to be cut off.
Once the part was free, the rest of the repair went quickly . At that point:
- Pull the element leads enough to get to the plastic connector
- Disconnect the old part
- Connect the new part
- Re-attach to the bracket with new screws.
Once the part was free, the rest of the repair went quickly . At that point:
- Pull the element leads enough to get to the plastic connector
- Disconnect the old part
- Connect the new part
- Re-attach to the bracket with new screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Montello, WI
- Parts Used:
- 12001655
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver
Temp out of wack
replaced heat sensor
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Isaac from LATHRUP VLG, MI
- Parts Used:
- 12400035
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven taking to long to preheat.
Accessed igniter removed 2screws holding it.unpluged igniter installed new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ernie from Fremont, CA
- Parts Used:
- 74002312
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broiler front drawer slides broke
I noticed the drawer on the broiler was sliding crooked and found the plastic slides had broken. Of course I thought it would be a hassle and not worth the time to fix it. I would just "live with it". Boy was I wrong, it was probably the simplest fix ever. It was easy to get the correct parts from PartSelect with their exploded and concise diagram. The parts were ordered and delivered in a couple of days. It took me all of 10 minutes with a screwdriver to make the repairs. Now it is a good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from PEORIA, IL
- Parts Used:
- 12400035
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The oven igniter came on but the gas valve never turned on.
1. remove oven door 2. remove racks and oven floor 3. remove oven burner 4. unhook igniter 5. install new igniter 6. tuck wiring back in as reinstalling burner 7. put in the insulation supplied in kit 8. install floor and racks. 9. install door. 10. test system 11. oven came on. SUCCESS
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from SHOREVIEW, MN
- Parts Used:
- WP9781049
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
left cover for the oven light broke when trying to replace the bulb
Ordered the part. when it arrived-quite speedily, I just unpacked it and put the cotton gasket around the glass and screwed it to the proper place in the oven. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Duarte, CA
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven Was Not Getting Hot
First I want thank you for being there for me . If it wasn't for you I would be having thanksgiving at my mother inlaw first iremoved the two screwsthat holds thy element in place. I then pulledthe element out about 3 in and disconnected the two wires . It's easy as 1. 2. 3
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from Monroe, NY
- Parts Used:
- WP5504M003-19
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
floor panel heavily stained and warped
slide latches in rear of floor panel forward and remove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from FITCHBURG, MA
- Parts Used:
- 12001655
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
f1&f3 error> continuous beeping,oven stopped working after using the self cleaning mode
I located the temp sensor (top left). Removed the 2x Phillips screws and slide the wire out until the plug is thru the opening taking care not to pull to hard as to damage the end that you not going to replace. To install plug it in and push the wire thru and secure with 2x Phillip screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yafa (and David) from Bothell, WA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dana from Windchester, IN
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
oven wouldn't heat
removed 2 screws and unpluged ingiter plug ed new igniter in replaced screws and worked fine
Was this instruction helpful to you?
Thank you for voting!