L3521WRV Norge Range - Instructions

removed old clips and remaining parts of old seal...new part already had clips attached, so just snapped them into holes in oven door.

First I opened the door to the oven. Then I opened the box that the part came in. (knife) I then slid the oven rack out of the box and unwrapped the plastic, being careful not to bend or scratch the new rack. Now, this is the tricky part... I had to move the existing rack down one space to make room for the new one. Then carefully slid the new rack in, tipping it slightly and sliding it in. LOL

Turned off the power at the breaker box. Removed the two screws, pulled the element out about 3 inches, disconnected the two wires, reconnected the two wires to the new element, inserted element back into place, screwed in the screws...all finished...works great! Delivery was super fast...just a great experience all the way around.

Being a woman, I first cleaned the oven. Removed two screws holding the element in place. Pulled element out about 3 inches and disconnected one clip attached to a yellow wire another clip attached to a green wire. Put new element in connected clips. Replaced screws.

Pulled the oven away from the wall. Removed two screws inside the oven. Pulled old heating element out. When I did I heard a loud pop and and saw smoke. I assumed the element would not be electrically live if the oven was not on. That was obviously incorrect. I pulled the plug and then completed the installation. I went to chruch on Sunday and thanked God that I was not electrocuted. Now the oven works fine. My wife wanted the oven to die so that she could get a new alppliance, Instead I am alive.

Seriously your service was great. Your web site pointed me to the correct part, and it arrived the next day! I would definitely use your service again if I remember your name.

As I pulled the drawer looking for a pan stored in bottom drawer the drawer glide broke. The pictures of the parts were fantastic. Not being sure of which of two parts from the photos, I ordered two parts knowing that hopefully one would be the correct one and the other would not be the part I needed. Parts arrived and it was clear which of the two parts would fit perfectly.

I screwed in the part, and that was it , and I was relieved that the problem was solved! I kind of feel lucky that your company is in business! The other part is fully accepted and plan to send it back in for a refund. And oh yes, I solved my appliance problem under $20.00 - unbelieveable these days!

Thank you again for beng there!

I learned that I could clean the window in the oven door. In taking it apart I saw that the gasket had fallen into the oven door. I found the part online, it arrived in three days. I removed the metal part of the door, removed what was left of the old gasket and put in the new one. Put the metal part of the door back on, and it was as good as new.

Replaced receptacle but it was not the problem. After further inspection I believe that the problem is the switch. The switch is on order now from Part Select.

First I swiched off the circuit breaker just to be safe.Then I removed the two mounting screws and disconnected the the element leads. Very easy task, approx 5 mins. THANKS

It was very simple, pull off the old one, then I took some pliers and pulled out the fasteners. Took new gasket from bag and it just snapped into place.

First-my daughter needed her pizza and I didn't want to even think about the cost of a new range. So she did some research online about replacement parts. Lo an behold, Partselect.com was our answer.

We received the part in a few days and replaced it with just unscrewing a few screws.. AFTER we unplugged the range. We also used a tool that I would describe as a nail remover/lifter to get the end off of the wire connection. Needless to say, we were rookies and had no experience with this type of repair and were so proud that we were able to spend less than $30.00 to fix our oven.
Thanks to Partselect.com for making it easy to do this repair on our own.

Worst part of the job was removing the old screws that held the two old rectecles in place for the two burners I repaired. Once the screws were removed cut the wires stripped them and used the porceliean wire nuts provided with the kit. Easy job and good instructions.

First I shut off the power at the circuit breaker.Then I removed the racks to make room to work.I then removed the 2 screws holding the element in place and pulled both sides out approx.3 inches.After carefully disconnecting the wires,I put the new element in to place and repeated the steps backwards.

My husband did it. I was not there to see it. He said it took less than one minute, just snapped in and worked beautifully.

I removed the two screws that held the element in. I pulled the old element out and heard a loud pop. I didn't realize that I had to turn the oven off at the breaker to change the element. It blew the breaker and melted one of the connectors to the element. The wires didnt pull through the hole so I had to pull the oven out, take the back panel off, replace the electrical connectors, slide the wires through the holes at the back of the oven, connect the element and put it back in, now it works fine. Remember to turn the oven off at the breaker when changing the element, it could be a shocking experience otherwise.