NGW3J8EKSVW Norge Range - Instructions

Using a remote digital thermometer, noted that the oven temp reached operating temp, then fell 40-50 degrees, was slow to recover. After reading entries from others on your web site, removed oven floor and watched the burner operation. The igniter would light the gas at first, the temp would go up, gas would shut off. Then when the igniter came on again, it would glow for a long time before gas would come on.The replacement was very simple, even though one of the mounting screws twisted off, the remaining screw seems to be holding.Was a simple unplug old connector, insert new connector. The optional parts included in the kit were not needed.

Remove lower pan. This is tricky -- pull clips at the back of the pan forward (they may stick), Then push pan to back and lift forward portion up, exposing igniter and gas tube. Use nut driver or socket set to unscrew the two mounting screws. Had to use pliers at one point to pull on screws while turning as they were cross-threaded, perhaps due to heat. Cut wires to igniter. Pull out oven and look at exterior back of stove -- at bottom near the center opening. The power feeder wires to the igniter are red and terminate in a jack -- disconnect the igniter plug connector and pull the cut wire through. Back to the inside of the stove: you now have to force the connector for the new igniter through the insulation at the back. Pull some of the old insulation out to make this possible -- new insulation is provided in the kit. Then at back of stove connect new igniter plug to power feed jack. Then screw in new igniter with the original screws. I had to use pliers again while turning to force them past the cross-threaded area. Replace bottom pan and you are in business, saving a lot of money!!

Replaced the ceramic glow ignitor by removeing the two screws holding it to the mounting bracket. Gas and electric were tturned off. Unplugged the ignitor from rear of oven. Installed new switch in the same way and if worked perfect. Part was ordered online for $48. I saved one hundred dollars by doing it myself. My outdoor grill was harder than this.

snaped them into oven cavity attached temp bulb job complete

very easy

Screwed in light bulb and glass protector

Well, this wasn't my first rodeo, this is the second ignitor I have replaced in my oven, first being the broiler. It is very simple, unscrew the old one, screw in the new one. The hardest part was cleaning up the mess I found UNDER THE OVEN!!!!

open oven door remove bottom tray pull off two screws unplug wire remove old part install new part

I removed the oven door and floor, removed the two screws holding the old part in place, unplugged it from the wiring harness and plugged in the new part and replaced the screws. Fixed in 5 minutes.

Pulled out the plug, pulled out the stove, removed the oven door, pulled out the lower shelf and racks. Used a nutdriver to remove the 2 screws from the bracket, disconnected the old ignitor, new ignitor was an exact replacement, put back in the screws, pushed back the stove and plugged it back in....Was back in business in a matter of seconds!!

I removed the various trays and racks to gain access to the oven igniter. I removed the one screw that held the wiring in place that goes into the body of the oven and pulled out the wires. I removed the wire nuts and safe ended the hot wires. I removed the two screws that held the igniter in place and replaced it with the new one. I reconnected the wiring with the wire nuts , pushed the wiring back into the body of the and stuffed new packing material into hole and reattached the plate on the back of the oven. Turned on the oven and it ignited immediately. A very easy job to complete. I would suggest to others to turn off the power. I knew what I was doing by working it "hot".

My son removed the pan above the ignition switch, using only a screwdriver. He checked it against the excellent website photos for compatibility with what you had to offer. I order it and it was here in Houston within 2 days of the order. Took 20 minutes to remove and compare and 7 minutes to replace the old with the new. A piece of cake.
Best thing was that the oven/stove is 29 years old and I thought I would have to buy a new one (approximately $700 for comparable)and I am a Senior Citizen. So for $48.98 and lots of elbow grease to clean the stainless steel top etc. I have a dandy, operating, dependable piece of cooking equipment !!!!

the igniter would glow but the gas would not flow...
i would have guessed the valve was bad, but every one else thought it was the igniter.. they were right. verry easy to install. the stove worjks like new.

Un-did the old one put in the new. Iam 63 years old and a woman. Repair men wanted 500.00 plus to come out and repair I did it for cost of igniter in 15 min. Oven works great! Thanks parts select for making it so easy!

I removed the two screws holding the ignighter on, pulled it a few inches, disconnected the plug, plugged the new ignighter in, tightened the two screws, turned on the power, and it worked. 1,2,3.