B995CXM5P Maytag Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mary from Salisbury, NC
- Parts Used:
- WP7406P012-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
heat element wouldn't heat after 30 years of cooking
Pulled screws loose from element, pulled old element out and replaced with new..really simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tom from cincinnati, OH
- Parts Used:
- WP7406P012-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lower element in oven not heating.
Removed, tested and measured the old element. Got on line to find the part and ran across Part Select. Ordered and received the part in three business days. It was an exact fit and in good order. The total operation including removal and replacement of the element, locating and ordering the part only took about thirty minutes.....and that includes the ten minutes it took me to find my #2 Phillips screwdriver! : )
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Prescott, MI
- Parts Used:
- 7201P036-60
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Burned up oven door gasket needed replaced.
I started by removing the door, then trying to remove all of the screws in the oven casing. Of course the very middle screw in the bottom of the oven was rusted and dammged by use. I had to use a drill bit and remove the old screw. After dissasembly of the oven casing, I found that the lip that supports the gasket was rusted and burnt away about 3/4 in. I placed the new gasket in and found that when closed it covered this defect and sealed. I reassembled and cheked for operation.Ok! Imortant--remove the elements before removing oven casing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- NORMAN W from Waleska, GA
- Parts Used:
- 7201P036-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
gasket was leaking heat from oven
removed old and installed new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Abilene, TX
- Parts Used:
- WP7406P012-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The bake element was corroding.
I turned breaker off for oven, removed screws from element mount, pulled the element out about two inches, then slid wire connectors up to unhook from element. Then set new element in, slid wire connectors on to back new element, then used pliers to make sure they were tight and secure by squeezing them, screwed element back in, turned breaker back on. Turned oven onto bake and left on for few minutes while it burned chemicals off element. Very simple!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from Dequincy, LA
- Parts Used:
- WP7406P012-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven element burned out
Removed old element with philips screw driver, reninstalled new element in reverse of removal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mark from Georgetown, TX
- Parts Used:
- WP7406P012-60
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
old lower element burned through, broke
found the element using visual grids supplied on the website. Measured old element and matched up with another after finding out that Whirlpool parts are interchangeable. Turned off power at breaker box. Replaced in 10 minutes.Fired it up to test at high temp for about 5 minutes.
Was this instruction helpful to you?
Thank you for voting!