79F-5EXW (15X) Maytag Range - Instructions

Repair went fine, insert helped, just take your time and remember the way you took out. Started without takeing door off, I am to short and door comes off easy, unscrew the two screws holding element leaving one not quite off then the back two screws then go back to upper screw remove and element will pull out, remove 3 wires remembering the order, Wiring is a little tricky (in the stove-just 3 plugins), just pay attention and will go smooth. Then remove element and go backwards and presto your done.

Turned off power at panel. Removed 2 Phillips screws holding broiler element support in place. Squirted 2 additional Phillips head screws attaching element to back of stove with WD-40 and removed screws. Slid element out to access electrical connection and used short phillips screwdriver to remove. Reattached electrical connection to new element with short screwdriver (no fun as you are cantilevered into the oven and have to hold the element, the screw and the screwdriver to do this). Slid element into support and screwed support to top of stove cavity to align element. Installed screws holding element onto back wall. Turned on power and ran element long enough to dissipate WD-40 fumes.

This was too simple, turned off the power to the oven, undid the two screws, unplugged two wires, plugged wires into the new element, fastened the new screws and turned the power back on. Turned on the oven, what do you know, it works again!

The element did not come with instructions and none were needed.

Awesome, just awesome, you guys are great and I will use you again and again.

This was an easy thing to do. Take the two screws off the back, pull the wires out, pull off the connectors, get the new element, replace the connectors, make a hole in the insulation, fish the wires back behind the insulation, screw the mounting screws and turn it on. The only thing I did extra is clean the bottom of the oven because with the element out, it's easy to do.

unscrew the old ones and replaced the new one - easy as that! Savings of over $300.00 if I need to buy a new one! Thanks for the speedy service after I ordered it.

Simply removed old element,2 screws,clean'd oven b/4 install'n new one,reconnect'd 2 wires,2 screws & yea oven wrks again. My husband was very happy as the oven is 34 yrs old,I just copied the model #,went 2 u'r web site,& we r very happy campers,so thank you very much.
Debbie A. Martin

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Went online and Googled for oven element by providing the serial and model number. Partselect popped up. I submitted the order and received and installed the new element within 5 days from start to finish. I recommend this website for replacement parts.

Found the model number, called the local parts store, they quoted $60 + $10 shipping because it was a warehouse order or something. So I came hear and got it for $42 + $7 shipping!

Turned off power, unscrewed the element, disconnected the clips from broken element, connected them to the new, screwed in the new element, and it was done

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, that were clipped on. slipped them off connected the new element screwed it back into the oven.

First, I want to say that this part arrived within 24 hours of placing the order. I was plesantly suprised. My husband did the repair and it was super easy. We had no problems.

Thanks PartSelect!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Connected the wires to new element, pushed wires back into the back wall, re-installed screws.

Determining the correct bake element to order was the most difficult part. Once I received the part, it took me 2 minutes to unscrew the back panel, detach the wires, connect the new wires and re-connect the back pannel - turned the oven on to test - and we were all set just in time for Chistmas baking.

Very simple, unscrew the old element. Remove the electrical spade connectors and reverse to install new element. The folks at parts select.com were very helpful and even after I ordered the wrong part, the return process was hassle free. Prompt shipping, very happy.

Pulled the old one out and installed the new one