PGR4410CDQ Maytag Range - Instructions

Removed oven door by opening slightly and lifting straight up. Pulled out racks and removed bottom of oven. Unscrewed wingnut and removed burner shield. Removed 2 screws that hold igniter and unplugged the connection. Reverse the procedure to put it all back together.
Be patient, it takes a few moments for it to begin heating when you first turn it on.
So easy a woman can do it ! I know,(I am one).

I first removed the screws inside the oven,let the tube that the flames come out of hang down,removed the screws from the igniter. Then I took the cover off the back of the stove and unplugged the old igniter and plugged in the new one. I put all screws back and put every thing back in place and the oven has been heating up every since. Thank you parts select. My husband is a otr trucker and won't be home until the 20th of this month. One less item on his "honey do list".

Husband did repair. He removed the
the ignitor. Was a little difficult to remove. I couldn't tell you what he did and in what order.

Ordered the broiler igniter that matched my model from part select and installed. Easy and part works as it should. Only took a few days to get here and saved me $40 by not purchasing at a local parts store as well. Will use part select if there are any future needs.

one screw holds the cover to the connector. one screw for the burner tube to the oven frame. two screws hold the ignitor bracket/assembly to the burner tube. that's it. take four screws off and disconnect. connect and put four screws back on.

Simple... unscrew the 2 screws and unplug the electrical connection to uninstall and just the opposite to install.

I removed the oven racks, the bottom of the stove and a v-shaped cover that was over the heating element. The old gas ignitor screwed off easily after I put W-D 40 on the nuts. I un ooked the old gas igniter and replaced it with the new one. The oven lit immediately after I replaced everything. I am very proud of my self, I feel like a femal Bob Villa. I almost bought a new range. Boy am I happy!

Put the back of stove on blocks of wood to get high enough to screw the new leg in.

Removing the old oven bottom was easy...as it was already outside of its slots. Installing the new one was pretty easy. I placed the oven bottom in the front slots first...then the rear slots...no tools necessary.

Make sure all burners on stove top are off.Half twist burner top to separate burner from stove top.The burner slide fits over the metal tube that transports the gas to the burner.Remove the 2 slip fit connected wires from the underside of the burner.They should be of different sizes so no worries about incorrectly re-attaching them.The igniter has 2 philips screws holding the igniter to the burner, Remove those and the igniter will be able to be removed with a little wiggling.Insert new igniter thru the hole in the burner and secure with the 2 screws. Reattach wires , place burner back on top making sure the wires aren't being crimped when the burner slides over the aforementioned metal tube and twist burner to seat in stove top, turn on burner to confirm igniter now ignites properly.

I took pliers to get the old one off, and popped the new one back in its place, and it fit perfect.

I was looking at replacing the stove and saw the $1200.00 price tag! So I found this web site and paid $100.00 to fix my old one. It was very simple. I twisted off the old burners by sliding off the two connecting wires. Cleaned the area around the seating area of the burners. Hooked the wires on the new burners and twisted them back in place! Tested them to insure that was the problem and was done! Thank you for saving me $1100.00!!! Next I am getting grates so the whole stove will look band new!

Firmly grasp burner turn counter clockwise while lifting. Photograph the location of the wires. Remove with a Phillips head screwdriver. The igniter will lift and turn one quarter turn then pull through bottom. Reverse the steps to install the new igniter. Test knew igniter. Put tools away

Unplugged the Rang. Removed the oven door. Removed the lower cover for the Bottom heater. Removed the two screws that held the igniter to the burner. Went to back of oven to disconnect the igniter. removed the old igniter. Installed the new Igniter in the reverse order.

First I did was to google the problem I have. There several video how to solve the problem. It show me different ways to solve my problem. I just follow the instructions. Thank to google without it, I am lost. I may add, that google is a big saver for me.