YMER8880AS0 Maytag Range - Instructions

An easy repair. I just needed a screwdriver.
I watched the video that you sent me with the part. I followed the directions in the video and the job was completed in 30 minutes!
Easy Peazy!! I’m back to cooking!

I watched a video on google on how to replace the element and then looked on the internet to order the element. When the part arrived, I pulled the range out and unplugged it. Then I watched the video again and followed the techs instructions to remove the element and replaced it with the new one. It’s a very simple process that I think almost anyone can do . The online videos make the job easier because they show exactly the order of disassembly and assembly, and Part Select helped with finding the right part and shipping it in a timely manner. Thank you!

Repair of oven sensor easy to install; however, product did not resolve the problem. Returned new sensor and awaiting refund (2 weeks passed so far).

Opened the breaker for the oven. Verified the power was off. Removed the racks from the oven. Using a screw driver removed two screws in the back of the oven holding down the steam bake bottom of the oven, pulled up from the back to get the pan out. Removed the screw holding the front of the element in place. Removed the screw in the shiny metal of the element at the back. Gingerly pulled the element to the front and as the element stopped slightly turned the element to let the prints come out. That part was challenging to get the angle right so not to damage the wires. Using a small Phillips screw driver I pushed in on the connector latch on the terminal and then pulled the terminals off the element one at a time. Follow all the steps in reverse to install the new one.

Shut beaker off
Unhooked wires on element back of stove
Removed all racks
Unscrewed lower plate cover
Removed element
Inserted new element
Rebooked wires to element
Reinstalled cover plate
Turned breaker back on
Turned range on and let heat up
Turned it off
Reinstalled racks

Unplug the appliance, remove the bottom cover inside the range and the cover in the rear to unplug the heating element. R&r the element, reinstall the covers and test for proper operation.

1) unplugged rnage from wall
2) took off back plate to unhook electrical from element
3)took door off of range for ease of access
4) removed the 2 screws i the back of tha bottom panel
5) removed 1 screw in front and 1 screw in back to be able to remove old element.
6)remove element and replace with new one.
7) reinstalled both screws and the bottom panle.
8) connected electrical to new element
9) replaced back cover and plugged in unit to wall
10) put range back in place.

Took out the bottom tray and the back cover panel, unplugged the old element and plugged the new one in and reassembled

I read the help section and it said that the element was likely to be the problem (84%) and the fuse had a 14% chance to be the problem so I purchased both. After watching the video I tried the element first and that's what it was so I returned the fuse, Thanks for the help and video.

The company said it would cost me $698 to repair. I had a 2 year warranty and that was 2 months out of date.

Again thanks for the help.

Removed rear panel disconnect power from wall removed old switch and replaced with new switch and reassembled

The repair was successful. I know the dual element burner was good because it operated at full heat. After installing the dual element control switch, the burner was operating as expected with no further issues. After the back was removed, the dual element control switch was easy to access. After removal of the two Philips screws (and the knob), it's easy to pull out the switch to pry off the two cable harnesses (which are keyed). Removal of the cable harnesses was the hardest part because they come off very hard. I used a flat blade screwdriver to help pry off the harness. Installation of the new dual element control switch was very fast/easy, along with the back cover.

I pulled the range out from the wall, then unplugged it from the wall outlet. I removed the oven door & set it aside. Removed the screws covering the rear wiring shield, then disconnected the 2 leads from the bake element. Unscrewed the screws holding the oven floor pan, then unscrewed the screws holding in the original element. Replaced it, screwed everything back together, and pushed the oven back against the wall. Took me about 30 minutes, and now the oven works as well as it did when we first bought it.

Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

The You Tube video for replacing the Element was very useful. Let me know exactly how to proceed - it was easy.

I didn't. Don't know how to get to light bulb to change it for this specific model