MGR5880BDB Maytag Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from Reno, NV
- Parts Used:
- 74003387
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
old bulb fused into old socket.
removed old socket and replaced.
I was VERY pleased with Partselect. Easy to find part, it was in stock and fast delivery.
I was VERY pleased with Partselect. Easy to find part, it was in stock and fast delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from CHESTER, CA
- Parts Used:
- 74004053
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
replace igniters
Watched u tube video as supplied and followed instructions. Had trouble getting burners off so cleaned around edge of burners with fine bladed knife as suggested by other forum user and used oil filter type wrench to remove burner. There are three bumps on burner that hold it in place so need to turn anti clockwise to remove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from NEW YORK, NY
- Parts Used:
- WP3412D024-09
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Broken burner - easy fix
The burner was leaking a rust colored dirt and shooting flames all over the place. The top came off and I needed channel-locks to get the bottom half out. The wires were hard to get off and I broke one connector off so I soldered the wire on to the new part which fit the stove top perfectly. It still took less than a half hour to replace. Without problems it should take about 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from East Northport, NY
- Parts Used:
- 4318047
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set, Wrench (Adjustable)
Ice maker working with no production of ice
Turn off the water source and unplug freezer. Remove copper tube and then remove valve from back of refrigerator. Disconnect plastic tube and power connection. Mark power connection plug top with a "T", this reminder helps with the new valve. Plug power and plastic tube into new valve and screw assembly back into refrigerator. Using a wrench, connect copper tube into valve. Restore water source and plug back in in freezer. Within a couple hours, ice production was back.
Like the other repair stories (that helped me), this job was very easy.
Like the other repair stories (that helped me), this job was very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Francis from delavan, WI
- Parts Used:
- 74007498
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven does not heat but broiler works
Oven and broiler have two seperate igniters. Broiler worked but oven did not heat. Oven igniter located under metal pan at base of inside of oven. remove pan by lifting, and remove completely from oven. Igniter under this pan and held in place by two srews. Remove screws, unplug from cable, replug in ne igniter, replace two srcews and pan, and you're done! this part cost about $50 and I installed, last time Sear replaced =$300.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from Monroe, NY
- Parts Used:
- WP5504M003-19
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
floor panel heavily stained and warped
slide latches in rear of floor panel forward and remove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yafa (and David) from Bothell, WA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gordon from LYNDEN, WA
- Parts Used:
- 74007498
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
No problem
Very easy install. Works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alfred from BUDA, TX
- Parts Used:
- 74007498
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
My igniter burnt out. My oven stopped lighting up.
I ordered a new igniter and when it arrived, i removed the door from the oven. It just lift's off. I had to removed two screws from the bottom plate to gain access to the igniter. Remove the two screws from the igniter and unplug it from the back of the lower back of the stove. Place the new igniter where the old one was and plug it in. Put new screws in and tighten them down. Put the bottom plate back in its place with screws tightened. Put oven door back on and turn on the oven. That's all there is to it. Your done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dhirajlal from SKOKIE, IL
- Parts Used:
- WP3412D024-09
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Burner igniter problem.
Replaced with a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from MOUNT HEALTHY, OH
- Parts Used:
- 12001655
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Had an F2 message go off then F3 when I tried to turn the stove on
Unplugged the old temp sensor at the back of the stove. From the inside I removed the 2 retaining screws. I taped a string to the old wire and pulled it through so I could pull the new harness through on the new sensor. When the new sensor arrived I installed it in reverse order. Easy peasy. Works great!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Bloomfield Hills, MI
- Parts Used:
- 4318047
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Old Valve was dead
This was very easy and pretty fast to do and its working great...all for $40 bucks ! you can do this...trust me!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Fresno, CA
- Parts Used:
- 74007498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven would not maintain temperature
First I removed the oven racks, then the bottom cover over the burner. I then unscrewed the two screws holding the igniter on to the bracket on the burner tube. I then removed the storage drawer and loosened the two screws holding the metal shield in place. I then unclipped the electrical connection to the ignitor and pushed it up past the insulation. I then went back into the oven and pulled the wires and connector through. The old igniter was out!
Installation of the new one was just as easy. Screwed the new igniter onto the backet, stuck the electrical connector through the hole in the back of the burner tube, and connected it. I then replaced the shield and the storage drawer, replaced the bottom pan over the burner tube and the racks. The stove works perfectly and my wife is happy. The job couldn't be easier.
Installation of the new one was just as easy. Screwed the new igniter onto the backet, stuck the electrical connector through the hole in the back of the burner tube, and connected it. I then replaced the shield and the storage drawer, replaced the bottom pan over the burner tube and the racks. The stove works perfectly and my wife is happy. The job couldn't be easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Grace from Lincoln, RI
- Parts Used:
- 12002359
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
rusted trim at bottom of glass /top and bottom doors
Bottom door/ simply removed the screws where neccessary and slipped the glass off with trim attached , then carefully seperated the trim and window , cleaned glass and put new trim on with the tape shims in place. reinstalled screws. Top Door/ using trim made for the bottom door , I seperated the bottom from the sides bydrilling the welds then used the existing sides with the bottom section of the new piece which I had seperated . It worked very well and there was no way to simply buy trim for the top door. It is Paul
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rhoda P. from Secaucus, NJ
- Parts Used:
- WP3413F018-19, WP3401F075-19
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I needed a broiler pan
I took the broiler pan out of the shipping container and put it in the oven.
Was this instruction helpful to you?
Thank you for voting!