LBR1415AGW Maytag Range - Instructions

1. Turn off the gas (propane)
2. Unplug the oven.
3. disconnect the gas line and pull the oven out.
4. remove the back panel to access the igniter.
5 disconnect the igniter.
6. unscrew igniter/gas assembly and remove from oven (two screws).
7. unscrew igniter (two screws)
8. replace igniter with new.
9. reassemble in reverse order.
10. turn on stove.
11. Happy wife, happy life.

followed instructions from repair manual.

First i removed the two screws that hold the element in place. I then pulled the wire out of the hole and disconected the plug. then plug in the new one, put the two screws back in, and checked it to see if it worked,It worked like a new one! So as my reward my wife baked me cookies!

It took all of 10 mins. Open oven door slightly lift to remove.took out shelves and bottom of oven,lift at back to remove.Two screws hold the Igniter, was able to pull the connector into the oven to change. Oven works great!

This is simple for most people - unscrew and remove the bottom oven floor pan. There is the igniter, removed with two screws with a 1/4 nutdriver. However, my problem was that when I unclipped the old igniter, I dropped the over part of the connection, it fell down the hole, through the insulation, to the bottom of the stove where the wiring is. I had to pull out the stove to get to the connection, push it back up the hole to the oven, then install the igniter. My advice: do no lose your grip on the oven wire whatever you do. Otherwise, it was a snap, even for a klutz.

Bought the igniter, replaced it with the old one and it works great.

removing the screws holding the burner together was impossible. they snapped off and I had to drill them out. that took the most time. after that it was 100% easy hookup. clean up of the burner was done with a wire brush. good quality products. thanks.

I had to use a dremel to grind the heads off the rusted in screws that hold the burners to the stove top then drill out the screws and use larger sheet metal screws to reassemble. Don't lift the stove top much with the burners attached or you'll bend the gas lines. Two screws inside the top oven hold the top down. Without the rusted screws it would be an easy job.

Unplugged the oven from electricity. Took off the bottom(Floor) of the inside of the oven. Checked that the new part looked the same as the old. It did. Then I checked the back of the oven, had to take off a cover, and the connector in the back was not the same. I did not that it had the same two wires so rather than send it back, I figured I could make it work. I started to take off the old piece by unscrewing the two screws. They were a bit rusted, one came off the other I had to hacksaw and twist off. I cut the old connecting end off of the old part and the end off of the new part stripped the cover off the ends of the wires, and put the old end to the new part, having also put the old wire covers over the new wires. then twisted the end together and wrapped the in electrical tape. I had to take the piece that held the new part out of the oven the tried to use the one semi-good old screw, then some newer screws, then finally used some new nuts and bolts to connect the part tightly. put everything back together and it worked.

1)Completely removed racks, oven bottom and broiler drawer to access unit. 2)Shut off gas supply by by pulling horizontal lever on left side of safety valve forward to close valve. 3)With screwdriver, removed heat shield covering safety valve and connector from igniter. 4)With socket wrench, removed the two mounting screws on igniter. 5)Installed new igniter, connecting to safety valve. 6)Turned on gas supply by pushing horizontal lever to left of safety valve back to open valve (see step 2). Turned on oven to test. 7)Upon gas igniting, shut off oven and install oven components in reverse order.

removed oven door and shelves and lower pan and replaced igniter

I am sure I saved a bunch of money for an outside repair. It was so simple I was embarassed that I did not attempt the repair sooner. Removed two screws from old burner head lifted it up unplugged the electrode wire replaced with new burner head put the two screws back in place and I was finished.

Broke the same day I installed it

1.) Remove door from hinges (open slightly and pull up). 2.) Remove racks. 3.) Remove oven floor to expose burner. 4.) Remove wing-nut and burner cover. 5.) Remove two ignitor mounting screws. 6.) Pull wires and connector through back wall. 7.) Connect new ignitor and mount to burner. 8.) Replace components in reverse order.

This is a no brainer. I am only doing this because you asked. Pull out the stove, tilt it back, remove broken leg, install new leg.