MES5875BCW21 Maytag Range - Instructions

Pull range out 6 inches. Open door to 45 degrees and pull up to remove door. Remove both side plates, two screws each side. Remove both hinges by loosening two small bolts on the front of range that connect to the hinges. Place new hinges in place. Bolt hinges using bolts you removed, replace side panels. Slide door on hinges and push back range.

I slide the range out and unplugged it from the outlet. I removed the back of the oven ( 8 screws ) using a cordless drill and phillips bit then with a phillips screwdriver I removed the oven sensor (2 screws) then I installed the new sensor , reinstalled the oven back , plugged the range in , slide it back into place and that was it. This repair took about 10 mins and the oven works perfectly. Thanks !

Left oven off. Located sensor in pdf manual. Unscrewed mount, pulled sensor out to access connector. Disconnected old sensor, checked continuity(resistance) on ohms with multimeter. No continuity; connected new sensor, screwed mount back into place, turned on oven and baked cookies to check operation & it worked perfectly.

1. OPEN THE OVEN DOOR TO THE FIRST STOP,
PULL UPWARD TO REMOVE, ( IT WILL LIFT RIGHT
OFF)
2. LAY OVEN DOOR ON A FLAT SURFACE ( HANDLE
DOWN AND HANGING OFF SURFACE) WITH A
TOWEL TO PROTECT THE GLASS.
3. REMOVE ALL SCREWS AROUND THE
PERIMETER OF THE DOOR..
4. CAREFULLY SEPARATE THE DOOR FRONT AND
BOTTOM BRACKET BY SLIDING AWAY FROM
THE MAIN DOOR INNER-ASSEMBLY, ( THE
FRONT GLASS IS HELD BY THE TOP CHANNEL.
5. TURN THE MAIN DOOR INNER ASSEMBLY OVER
AND REMOVE THE HANDLE ASSEMBLY TWO
ATTACHING BRACKETS.
6. REMOVE THE ATTACHING BRACKETS FROM
THE HANDLE AND ATTACH TO THE NEW
HANDLE.
7. THE DOOR GLASSES CAN NOW BE CLEANED
8. ATTACH THE NEW HANDLE ASSEMBLY
9. REASSEMBLE IN REVERSE ORDER.
( BE CAREFUL WHEN SLIDING FRONT DOOR
GLASS INTO THE TOP DOOR CHANNEL}

Repair was very simple. Took the door apart in layers, replaced the glass and put everything else back. it took longer to clean the stove than it did to actually take it apart and put it back together. guess i didnt need to be that much of a clean freak!

Unplugged the stove and removed the back panel, disconnected the wires from the old receptacle, removed it, inserted the new receptacle, connected the wires, put the back panel of the stove on, plugged in the stove and then checked to see if the bulb was now burning. Success!

The plastic attachment on the oven door handle broke on one side, and of course the whole handle had to be replaced. I attempted first to super-glue the broken piece, but naturally, that didn't work. I found the necessary piece very easily thru PartSelect.com's web page, and had the replacement piece within a couple days. The most difficult part of the whole operation was figuring out how to remove the old handle. Once that was done, the replacement took approximately 15 minutes. Thanks PartSelect.

I took the oven door apart, pulled out the broken fragments of glass and replaced it with the new glass. I should have taken notes as I took the door apart because it was a bit tricky to remember how all the pieces fit back together.

I was very impressed with how quickly the parts were shipped and the quality of the packing materials to protect the glass as it was shipped.

I didn't. Don't know how to get to light bulb to change it for this specific model

I viewed the YTube Video that showed exactly how to remove the door and all the other parts for replacement. Excellent video shows and explains how to remove, replace, and re-attach the handle and the door.

Removed the approximatly 10 screws that hold on both the upper and lower pieces of sheet metal that cover the back of the oven. Removed the screw holding in the temp sensor. Unplugged and removed the old sensor. Plugged in and installed the new sensor (using one of the included adapter wires supplied with the sensor). Put the 2 pieces of sheet metal back on and plugged in the oven.

The first set of racks did not fit. I called the Service rep, gave him the model number and exchanged the racks for the new ones. The new ones fit perfectly and the service was excellent. I would definitely recommend PartSelect.com to anyone who wants to deal with a company with excellent service, parts and representatives who know their stuff.

Remove the door, remove screws from all sides

Remove sides and face of oven door by sliding down from under the oven handle trim.

Remove screws on 2nd light of glass and set aside.

Now you are at the inner door panes. their should be two in an insulated type unit.

Remove the remaining screws from the handle pracket and the permiter frame for the glass/insulation. Remove permiter frame and set aside.

Pull out inner door glass frame. get a pair of pliers and bend tab on frame up so you can pull the frame sightly apart, replace the glass, secure frame tightly around glass slide tab back into reciever slot and bend down ( you may need another person to assist in keeping both lights in the frame while trying to ben tab back in to place)

reassemble door as it came apart carefull not to over tighten the screws, they strip easy.

The video indicating •unscrew old sensor, •pull wiring, •unplug old sensor, and •plug in replacement was good until I pulled the old one and saw wire nuts behind the small square hole! After some research, I learned that the nuts COULD come through that small hole with use of needle nose pliers. One of the wire nuts had the edges pinched off (chipped) in the process. Then I learned about ceramic wire nuts, which I'd never previously encountered. Very important if you don't want to melt your nuts! I cut and stripped the end of a disconnect plug to the stove wiring and now I have a plug in place; which, hopefully, I'll never need to use.

1. Open oven door to first detent, then pull it up off the hinges.
2. Pull oven out from counter 10-12 inches.
3. Hinges are accessible from the outside of the oven.
4. Remove 2 screws on each hinge and remove old hinges.
5. Put new hinges in place and try to insert mounting screws.
6. Wonder why screws won't start in threads.
7. Examine new hinges and notice they are not threaded for the screws.
8. Screws are not self-tapping, so go to basement and get tap & die set.
9. Use 10-24 tap to make threads in new hinges.
10. Put new hinges in place and insert mounting screws. Tighten.
11. Pull hinges to first detent and put oven door on hinges.
12. Push oven back into place in counter.