MES5875BAB19 Maytag Range - Instructions

Pull range out 6 inches. Open door to 45 degrees and pull up to remove door. Remove both side plates, two screws each side. Remove both hinges by loosening two small bolts on the front of range that connect to the hinges. Place new hinges in place. Bolt hinges using bolts you removed, replace side panels. Slide door on hinges and push back range.

See description listed as problem

took off nobs, pulled stove out 2 inches to access front side screws,( has 1 philip screw on each side end and four nut screws under panel) pulled panel out and flipped forward and down, all switches exposed and took apart broken switch and installed new switch(PAY ATTENTION TO WIRING PATTERN), reverse order for install back. bingo!

Had this range for 6 years. My daughter turned on the burner and it went "pop". She was very upset. I found the best price at PartSelect, and ordered the same day.

the first burner arrived broken in the box. We contacted PartSelect, and they immediately sent another and rushed shipping. It arrived in excellent condition.

To replace the unit: First, I turned off the circuit breaker for the range. Then I removed the two Philips screws that held the cooktop down. Next I removed the nut screws holding the burner to the cooktop.

Then I placed the new burner next to the old one, and one by one swapped the wires (this way I was sure I had the right wire on the right connector). One of the wire connectors broke when removing it from the old burner. PartSelect had provided 4 repacement connector pieces (oddly, all of which were too small for the burner element). So I located a replacement connector at a local hardware store. Stripped the end of the wire and used pliers to fasten the new connector.

After all connectors were secured to the new burner, I screwed the burner to the cooktop, then closed the cooktop and secured it with the two screws.

Turned on the circuit breaker, and it works like new! Saved over $100 by doing it myself!

1. OPEN THE OVEN DOOR TO THE FIRST STOP,
PULL UPWARD TO REMOVE, ( IT WILL LIFT RIGHT
OFF)
2. LAY OVEN DOOR ON A FLAT SURFACE ( HANDLE
DOWN AND HANGING OFF SURFACE) WITH A
TOWEL TO PROTECT THE GLASS.
3. REMOVE ALL SCREWS AROUND THE
PERIMETER OF THE DOOR..
4. CAREFULLY SEPARATE THE DOOR FRONT AND
BOTTOM BRACKET BY SLIDING AWAY FROM
THE MAIN DOOR INNER-ASSEMBLY, ( THE
FRONT GLASS IS HELD BY THE TOP CHANNEL.
5. TURN THE MAIN DOOR INNER ASSEMBLY OVER
AND REMOVE THE HANDLE ASSEMBLY TWO
ATTACHING BRACKETS.
6. REMOVE THE ATTACHING BRACKETS FROM
THE HANDLE AND ATTACH TO THE NEW
HANDLE.
7. THE DOOR GLASSES CAN NOW BE CLEANED
8. ATTACH THE NEW HANDLE ASSEMBLY
9. REASSEMBLE IN REVERSE ORDER.
( BE CAREFUL WHEN SLIDING FRONT DOOR
GLASS INTO THE TOP DOOR CHANNEL}

Unplugged the stove and removed the back panel, disconnected the wires from the old receptacle, removed it, inserted the new receptacle, connected the wires, put the back panel of the stove on, plugged in the stove and then checked to see if the bulb was now burning. Success!

Repair was very simple. Took the door apart in layers, replaced the glass and put everything else back. it took longer to clean the stove than it did to actually take it apart and put it back together. guess i didnt need to be that much of a clean freak!

Left oven off. Located sensor in pdf manual. Unscrewed mount, pulled sensor out to access connector. Disconnected old sensor, checked continuity(resistance) on ohms with multimeter. No continuity; connected new sensor, screwed mount back into place, turned on oven and baked cookies to check operation & it worked perfectly.

I took the oven door apart, pulled out the broken fragments of glass and replaced it with the new glass. I should have taken notes as I took the door apart because it was a bit tricky to remember how all the pieces fit back together.

I was very impressed with how quickly the parts were shipped and the quality of the packing materials to protect the glass as it was shipped.

The plastic attachment on the oven door handle broke on one side, and of course the whole handle had to be replaced. I attempted first to super-glue the broken piece, but naturally, that didn't work. I found the necessary piece very easily thru PartSelect.com's web page, and had the replacement piece within a couple days. The most difficult part of the whole operation was figuring out how to remove the old handle. Once that was done, the replacement took approximately 15 minutes. Thanks PartSelect.

I didn't. Don't know how to get to light bulb to change it for this specific model

I viewed the YTube Video that showed exactly how to remove the door and all the other parts for replacement. Excellent video shows and explains how to remove, replace, and re-attach the handle and the door.

Removed door from oven by pulling up at the first stop point after opening the door. Removed the outer shell by removing 5 screws. Disassembled the inner door by removing 6 screws. Be careful with the insulation blanket (fits in a molded portion of the inner door). Glass windows can be removed (for cleaning) via a couple screws. Old gasket/seal is held in-place via spring-clips; just squeezed each clip, pushed each thru their respective holes, and pulled off the worn-out gasket. New gasket snapped in-place by pushing the clips thru the respective holes. Reverse the process to reassemble the door. You can do this job in 15-20 minutes. Took us longer because it took some elbow-grease (and patience) to clean the crud off the glass windows.

My grandson, age 15 did the replacement. Now, how easy is that!

Waited for my husband to do it, but when he didn't, I tried it. Very simple! Just pulled the old gasket out of the pinch pin holes in the door, then replaced it. Tuck the one end into the hole at the bottom of the door, then match up the little pinch pins on the gasket with the holes in the door - matches up perfectly! Be sure to tuck in each of pinch pins till they sort of "snap" into each hole. Took me 5 minutes, tops. Works great now, no more lost heat around the edge of the door.