MES5752BAB15 Maytag Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from VALLEJO, CA
- Parts Used:
- WPW10162384
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Gasket was worn out.
Put a new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gayleana from spokane, WA
- Parts Used:
- W10823711
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
back R burner of ceramic top stove went out - died
1st - UNPLUGGED appliance from electrical source!! then removed screws to open ceramic stove top, disconnected wires from dead element, plugged in wires to new element, closed stove top, turned on burner - it worked!!
only problem is that "hot burner indicator" does NOT stay lit after burner is turned off!
only problem is that "hot burner indicator" does NOT stay lit after burner is turned off!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Sneads Ferry, NC
- Parts Used:
- WPW10310274
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
bake element non operational
No instructions with part, so I had to look up on internet. This took more time than installing it. Think basic instructions should come with the expensive part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Houston, TX
- Parts Used:
- 7730P011-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Indicator Lens melted and fell back into the control panel
I took the back panel off, removed the old lens, installed the new lens. How easy to order from home, receive the part, do the repair and pay less than it costs to simply drive to the parts house. Cool....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Chapell Hill, NC
- Parts Used:
- WPW10162384
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Oven heat loss, door gasket needed replacement
The entire "project" took me less than 3 minutes, and required no tools at all! First, the saleswoman over the phone pointed me to the correct product for my problem ($30 less than what I thought I needed), and it arrived at my home within 4 days. Then, it was just a matter of pulling off the old gasket, and snapping the new one in place! Simple!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steve from mcminnville, OR
- Parts Used:
- WPW10310274
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
element burn out
unplug and plug in new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Norfolk, VA
- Parts Used:
- WPW10310274
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element blew up
took the old one out (two phillips head screws)and put the new one in. done. took about 5-6 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- svetlana from chicago, IL
- Parts Used:
- WPW10310274
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bake element needed replacement
replacement was very easy, took 5 min
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sherri from elk horn, IA
- Parts Used:
- 12001656
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
ovens wouldn't maintain temperature after preheat cycle
unplugged oven. removed 2 screws that hold the sensor in place, then removed the dozen or so screws that hold on the rear panel, unplugged sensor and fed wire through insulation. identified and installed correct harness adapter then fed new wire and connecter through insulation and connected to adapter. installed sensor retaining screws.plugged oven back in and tested function.no dice. unplugged oven once again. removed oven control panel and upon inspection of printed circuit board discovered 3 solder joints had failed. dang. resoldered failed joints and also sweetened up a few others that looked suspect. reinstalled controller, replaced all retaining hardware, and plugged in the oven. tah-dah!! works like a charm now. moral of the story is check the pc board first and save $50 for unneeded pats!!! or buy the controller from parts direct for $260ish. btw a roll of solder and soldering iron from an auto parts store cost around $10, learned to solder on you-tube $0. amazing all the home appliances yo can fix if you're not afraid to take a few screws out and poke around a bit. CHEERS!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROY LYNN from SEMINOLE, TX
- Parts Used:
- WP74011768
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Bottom oven door handle broke when someone tried to open door too soon following self-cleaning cycle.
We removed the door from the hinges by sliding it up. Then we removed all the screws holding the door together. We had to remove the screw securing the trim. Next we removed the screws inside the trim holding the old handle. We replaced the handle and trim and screws in reverse order. Finally, we re-attached the door by sliding it onto the hinges.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Abingdon, VA
- Parts Used:
- 74003645
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Inner glass pane broke during self-cleaning operation
I removed all the screws that held the trim and inner frame to the outside window unit first. Then, I removed a protective glass from over the two inner panes. Next after removing the frame that held the two inner glass panes together, I took the broken inner glass pane out and replaced it with the new one. Then basically I just retraced my steps and had the door put back together in about 45 minutes. You just need to pay close attention to your disassembly so that you are able to put the pieces back together quickly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from NACOGDOCHES, TX
- Parts Used:
- WP7403P239-60
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Burner control switch stuck on High
Pull out the range...hardest part.
Remove back panel.
Remove/install switch
PS,
This is second switch I had to replace. Try making them in the United States.
Remove back panel.
Remove/install switch
PS,
This is second switch I had to replace. Try making them in the United States.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Ticonderoga, NY
- Parts Used:
- WP74011767
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
handle broke on one side
The best I can say is to remove door. take screws out from the bottom and sides first. Clean all layers of glass before installing handle.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dale from SAINT PETERS, MO
- Parts Used:
- WP7403P239-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Front 8" burner stuck on high no matter where dial was set.
This range was easy. Only 4 screws under the front panel that allows the panel to come off. No need to pull the range out for back screws.
Replacement part was exact and worked perfect.
Turn off the circuit breaker for the range.
Remove the 4 screws under the front panel, one on each end and one one each side of the display/control panel.
Pull the bottom of the front panel out about 30 degrees and lift off the top.
Once panel is off pull of the dial knob, remove the two screws for the control and swap wires on at a time with the new one.. Reverse the procedure and all is good. You may need to use needle nosed pliers on the spade connectors if they are too tight to pull off by hand.
Replacement part was exact and worked perfect.
Turn off the circuit breaker for the range.
Remove the 4 screws under the front panel, one on each end and one one each side of the display/control panel.
Pull the bottom of the front panel out about 30 degrees and lift off the top.
Once panel is off pull of the dial knob, remove the two screws for the control and swap wires on at a time with the new one.. Reverse the procedure and all is good. You may need to use needle nosed pliers on the spade connectors if they are too tight to pull off by hand.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerome from RICHFIELD, MN
- Parts Used:
- 74003645
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Broken inner glass window.
Remove the door.
Remove screws
Clear out broken glass. Vacuum out small glass shards.
Clean all glass.
Reattach all parts.
Replace the door.
Smile!
Remove screws
Clear out broken glass. Vacuum out small glass shards.
Clean all glass.
Reattach all parts.
Replace the door.
Smile!
Was this instruction helpful to you?
Thank you for voting!