MER8800DS1 Maytag Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Yafa (and David) from Bothell, WA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from THE VILLAGES, FL
- Parts Used:
- W10779716
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
After watching the video, I said to my wife that this is a simple installation. However, I’m looking at the screws, I did not have the correct screwdriver to remove the screws. I had to go out and buy that. After that, it was not a problem.
I first shut off the breaker, then, after pulling the stove away from the wall, I unplugged it. I removed the two screws in the back of the stove which came off easily. I removed the two screws inside the oven and removed the bottom plate. I noticed the heating element I was changing had braces along the bottom. I had to remove the two screws and removed the burnt out element. The new element did not have the braces the original element had, but it fit in perfectly. Then I replaced all the screws, plugged it in and turned on the breaker and it worked. The only thing that we noticed is there’s a clicking sound every time the temperature increases. Not sure what that is.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from HARMONY, MN
- Parts Used:
- WPW10181986
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
temp level uneven
after watching the video, installed the temp sensor. Super easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rosalind from APOLLO, PA
- Parts Used:
- WPW10181986
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the oven temperature was not working right. I installed a new oven sensor. Works get now
Watch the video...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from HUMBOLDT, SD
- Parts Used:
- W11047668
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dual burner right front not heating properly
Purchased new switch shut off breaker unscrew the back plate remove front knob and two screws that hold it on remove the two electrical clips from old switch then reinstall in reverse order. Also watched the youtube video before hand, great help!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from ENID, OK
- Parts Used:
- W11594027
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven light kept burning out instantly
Replaced the oven light with a new one but it burnt out as soon as I turned it on. Therefore I decided a new socket may help.
My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.
The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.
I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.
Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564
My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.
The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.
I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.
Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lou ann from MARTINSBURG, WV
- Parts Used:
- W10779716
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bake element burned out
There is a good video on YouTube that shows exactly how to replace the bake element. Had mine fixed in 15 to 20 minutes. Saved me about $150 by not having to call repairman.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from VALPARAISO, IN
- Parts Used:
- WPW10531060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
No problem.
Wanted third oven rack. No problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandeep from EDINA, MN
- Parts Used:
- W10777162
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
screw came off
very expensive to buy the part but just tighten the screw intot eh predefined place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOSEPH from COON RAPIDS, MN
- Parts Used:
- W11594027
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Worn/Bulb Socket
It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from DEFIANCE, OH
- Parts Used:
- W11171119
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Burner went out
Two screws to remove glass top. 2 connectors to remove. Removed glass top and put it upside down. Remove 4 wires and 2 Phillips screws. Reverse steps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tim from KEENE, NH
- Parts Used:
- W10779716
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Oven heated really slow, no heat from the bottom of the oven
Very easy followed instructions from a youtube video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Salem, OR
- Parts Used:
- WPW10434452
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The dual element control switches were no longer regulating the burners properly (either on or off, no in-between)
1. Pull the stove away from the wall and unplug the stove from the 240 volt receptacle.
2. Remove the knob from the switch (it just pulls off).
3. Unscrew the top half of the back plate of the stove and removed (about eight or so screws).
4. Unscrew the two screws attaching the control switch in the front of the control panel (these were hidden by the control knob just removed).
5. Pull out the control switch and detach one at a time the two sets of wire connectors attached to the switch. In order not to confuse which plug goes where, attach each connector to the new switch as you remove them. (Note: the connectors may be quite tight to the original switch; do not pull on the wires but simply work each connector gently until it slides off. They will reattach to the new control switch much easier.)
6. Reinstall the new switch to the stove in reverse order of removal. Make sure that the control knob, when the switch is reattached, is in the off position pointing straight up.
7. Reattach the upper back plate of the stove. For safety's sake, do this before reconnecting the stove to power.
8. Plug in the stove and test to ensure that the switch is working properly.
2. Remove the knob from the switch (it just pulls off).
3. Unscrew the top half of the back plate of the stove and removed (about eight or so screws).
4. Unscrew the two screws attaching the control switch in the front of the control panel (these were hidden by the control knob just removed).
5. Pull out the control switch and detach one at a time the two sets of wire connectors attached to the switch. In order not to confuse which plug goes where, attach each connector to the new switch as you remove them. (Note: the connectors may be quite tight to the original switch; do not pull on the wires but simply work each connector gently until it slides off. They will reattach to the new control switch much easier.)
6. Reinstall the new switch to the stove in reverse order of removal. Make sure that the control knob, when the switch is reattached, is in the off position pointing straight up.
7. Reattach the upper back plate of the stove. For safety's sake, do this before reconnecting the stove to power.
8. Plug in the stove and test to ensure that the switch is working properly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- bobby from HERSCHER, IL
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
range would not heat right
very easy watched the howto you gave
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from The Villages, FL
- Parts Used:
- W11171119
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Electric burner element not working
Video said to remove screws and lift stove top off, remove contacts and ground. My stove top was hinged and required me to lift and pivot stovetop up. The burners were anchored to the stove base not the top. I secured the topso that it would not drop down and proceeded with repair
Was this instruction helpful to you?
Thank you for voting!