MERH865RAW1 Maytag Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- sandra from ROCHESTER, MN
- Parts Used:
- WPW10276482
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
broken bake element
removed bottom pan cover. removed broken element. replaced with new one.. simple. would buy from this place again. shipped super fast
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- pamela from MONROE, WA
- Parts Used:
- 74003645
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Inner oven door glass cracked.
Watch the video. Spot on instructions. Easy peasy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from BOYNTON BEACH, FL
- Parts Used:
- WPW10276482
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven wouldn't heat past 165 degrees
First things first...Unplug the unit...Then remove the center plate from the back of the oven (one screw) and take clips off element. Then on the inside, there are 2 screws near the back on the bottom panel. These were rusted on pretty good, so that's where the vice grips came into play. The entire job would've gone much faster, if I wasn't fighting with these 2 screws...After you remove the screws, tilt up bottom panel and remove. Then you just remove 1 rear screw & 2 bottom screws and slide out the old element. Slide the new one in, secure it with the screws and screw the bottom panel back into place. Go to the rear of the oven, slide the 2 clips on the element and screw rear plate back on. Plug the oven back in and that's it...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Georgene from Rock City, IL
- Parts Used:
- 12001656
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
After cleaning, F1-1 error flashed and neither oven worked
First I called a repairman and left a message. That was 3 weeks ago. So, I 'googled' the error message and determined what part I thought I needed. Ordered the part on Wednesday evening and it was there when I got home from work on Friday. I unpacked the part, got a phillips screwdriver and then watched the repair video on your website. About 20 minutes later I pushed my stove back in place and the flashing said 'set time'. Then I checked both ovens, and have since used both, and everything works!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from East Sandwich, MA
- Parts Used:
- 74003645
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Shattered inside glass when attempted to self-clean
Door was removed very easily. Outside trim pieces were removed. The rest came apart like a simple puzzle. Inside glass is very easily accessed. Upon assembling, time was well under an hour. Shipping was fantastic and I saved close to 200dollars between a service call and a repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Exeter, NH
- Parts Used:
- 12001656
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Replace the oven Sensor
The sensor is mounted in the top right side of the oven.An extra long screw driver helps to avoid damage to the sensor when replacing it.The connectors were the opposite to the old sensor and I did not see that there were adapter cables included. It might help to connect or tie these together as I only expected the sensor and did not look for adapters.I had cut the wires and used wire nuts when I found the adapters.The repairs works fine.
Mike
Mike
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Toledo, OH
- Parts Used:
- WPW10276482
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Baking Element melted and stopped working
Unplug appliance, unscrew small cover plate in rear. Disconnect wires from old element, may need to use needle nose pliers to wiggle clips off. Open oven door, remove false bottom to expose baking element. Remove baking element. Install new element, connect wires from rear, and replace covers and false bottom. Plug in appliance and test.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Riverview, FL
- Parts Used:
- WPW10276482
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven wouldn't heat
First I removed the oven door, then I removed the three screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then I connected the two wires to the new element , replaced the three holding screws and the oven door. ------END-------
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from FEEDING HILLS, MA
- Parts Used:
- WPW10276482
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven only got to to 170 degrees
The bake element in this oven is covered by a tray but after locating the screws for that and removing I could see the element was burnt so I just removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) then just reversed the procedure to install. Don't forget to unplug the unit first.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Sunrise, FL
- Parts Used:
- 74008681
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Glass broke on oven door.
Found serial # as advised on web site. Found parts listing & ordered part. Got it in less than a week .
Unfastened two screws on top of door. Inserted glass. Applied a little mastic to prevent it from coming out again.
Done & done.
Do I get a prize ?
Unfastened two screws on top of door. Inserted glass. Applied a little mastic to prevent it from coming out again.
Done & done.
Do I get a prize ?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Otto from Breezy Point, MN
- Parts Used:
- WPW10276482
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
lower baking element was fried and no longer worked
Turn of power to the range. The element lies beneath a metal cover. The cover is held down by two screws in each of the back cornors. The burner element is held by a screw in the the back and by two screws near the front. Replacing the element was a snap. With the screws removed, pull on the element until the connecting wires are exposed. Pull the wires from the element and attatch to new element. Replace screws, cover etc. Turn on power and note the time it takes to reach a preset temp. You may detect a slight oder form a coating on the new element. .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- trent from Dalton, OH
- Parts Used:
- WPW10276482
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
shorted out element
removed the two screws in the rear of the oven to access the element. once exposed I removed the four screws holding the element in place. Went to the ouitside back of the stove and removed one screw holding the shield to access the terminals for the element. Installation was in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eugene from Clinton, IA
- Parts Used:
- 12001656
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven Temperature was 50 degrees low
Took screws out of the back on the side the sensor was on, unplugged it & took out the two screws on the inside of the oven to release the sensor. Put new sensor in place with the two screws & used one of the adapters to plug in the new sensor. Put screws back in the back panel & turned on the oven which unfortunately is still 50 degrees low. Need a new clock with computer which is out of stock & unavailable. I was an electrician for 25 years so didn't experience any problems. It was a cheap thing to try.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chad from Johnston, IA
- Parts Used:
- WPW10276482
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Failed Bake Element
First of all, let me say how "Not Handy" I am when it comes to these things. I decided to give this part a try after my oven decided to fail on Thanksgiving Day, so I ordered the part. It arrived on time as promised and packaged very well. The on-line parts breakout and testimony from the other buyers were so helpful. I had our oven back up and running in less than 10 minutes.
One thing I would also recommend is that you burn the element once installed for at least 15 minutes to get the newness smell off of it and then it won't permeate your food items.
Thanks, Parts Select! You saved me over $900.00; the price it was going to cost me to buy a new oven. :)
One thing I would also recommend is that you burn the element once installed for at least 15 minutes to get the newness smell off of it and then it won't permeate your food items.
Thanks, Parts Select! You saved me over $900.00; the price it was going to cost me to buy a new oven. :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Max from Houston, TX
- Parts Used:
- 12001656
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
No temperature control
Turned off breakers to oven. Removed two screws that held oven in cabinet. Removed oven door by opening slightly and pulling up on door. Pulled oven out 1/3 of way. Took out four screws on top of control panel. Took oven light switch off by unscrewing holding ring. Removed temp knob on right by pulling. Removed start / stop knob same way.Removed glass straight out. Removed four screws that held elecrtonic clock conrtol board. Unpluged three wire plug from right side and the nine wire plug from the left side. Worked board out at and angle. Went backwards to connect and replace board, screws and door.Slid oven back in and tested oven after turning breakers back on, worked like new.
Was this instruction helpful to you?
Thank you for voting!