MER8875WS0 Maytag Range - Instructions

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Took off the screws on the back of the stove and took out the sensor, and put in the new one.

Removed door from oven. Removed 6 screws to dismantle door. Removed 3 more screws to remove hinge from door...reverse order to assemble.
Very easy

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

The range in my classroom had the leveling legs broke off by the summer staff. I ordered two new leveling legs and the night custodian replaced them in about 45 minutes and them leveled the stove. Parts were just as stated and easy to order.

Changing out the baking element was fairly easy. Shut off power at breaker. Remove the baking trays and the 2 screws at the bottom of the inside back of the oven. There are 3 screws to remove the element. Slide out the connectors and replace. Additionally, the baking element blowing resulted in a blown relay inside the control unit. Unfortunately it is an all in one unit that includes the touchpad PCU board as well. To replace it you must remove the upper rear panel off the back of the oven, remove the electrical connectors, remove the 4 screws and the unit. Put the new unit back in and go in reverse. Power up to test.

First, I received the element in two days. My local repair store said it would take them a minimum of 10 days to get the part. My husband replaced the element after watching the youtube "how to" video. He knew exactly what to do and did it in about 30 minutes. We were using the oven the next day. Thanks!

Removed stove from slot in wall. Bent rear left leg would not unscrew due to bent metal bracket. Used hacksaw to cut out leg, then straightened metal bracket with small hammer and was able to screw new leg in and adjust height by using level on stove before reinserting stove its slot. Recheck level after pushing back in place and adjust front legs if necessary. If not for bent metal receiving bracket, would have taken much less time. Still easy tho. R'cvd part in two days. Very quick.

First removed 3 screws from top of door and the 3 bottom screws. To remove hinges there are 2 screws on the bottom ends remove those and then there is 1 in the center of hinge remove slide out old hinges and install new ones.The hinges have to be in the extended position I then put the needle nose pliers on the top end of hinge because they kept snapping shut before it engaged with the receptacle I put on one side when it was in I released the plier and it hooked I then proceeded to the opposite side it shouldn't have taken so long once I used the locking plier I was done in 10 minutes.

I watched a couple of online videos to determine what could be wrong with my oven and how to fix it. I ordered the part and it only took a half day to arrive at my door. After removing 3 screws in the panel on the bottom of the oven to expose the bake element, I pulled the element from the wiring. Even though I was careful, one of the wires slipped away and could not be fished back out. So I removed a few screws from the back of the oven, easily found the wire and connected it to the new element. It was a pretty easy fix that would have been even easier if the wire had not slipped into the back of the oven. I am a retired female, and I strongly recommend saving a chunk of money by doing this job yourself.

Turn off power--Remove bottom cover inside the oven---Undo three screws holding broken element in place--Remove element by pulling out ,and carefully detach from power connection.Reverse the procedure with the new element.In doing this myself I saved $90 for a repairman to come and diagnose the problem, and another $90 to bring back and install the element which cost $62

Exactly how the video provided showed. It was pretty simple.I feel pretty cheesy about doing this myself. Thank You!

Remove the plug from outlet then shutoff gas. Remove the 10 screws hold the back panel of the oven. Unclip the connector of the temperature sensor from the main line. Pull the sensor straightout. Reverse the process install the new sensor. Couldn't be any easier. Oven working great. Calling in a reapairman would have cost $200 for parts and labor.

open oven door ,turn off power,use 1/4 inch nut driver. make hook to lift protective pan ,unscrew screws holding element,4 phillips head ,install element .turn on power and test elwment everything ok.