MER8770WW1 Maytag Range - Instructions

Watched video & did just guy in video did. Very easy job & the burner works like new.

Turned off power at circuit breaker. Removed 4 phillips screws from area over oven door. Pulled control panel out and twisted to clear top rail. Pulled two wires off of old switch.Pulled old switch through panel. Inserted new switch. Attached the two wires to new switch. Replaced panel and inserted four screws. Turned on power - it works!

after watching the video, installed the temp sensor. Super easy

Watch the video...

Pull oven away from wall and unplug. with the oven door open, remove 2 rear screws holding down the element cover and pull element cover out of the oven. remove 2 screws holding element down to the bottom of the stove, and one screw holding the back of the element to the rear. now go behind the oven and remove the access plate to the element power connection (one screw). Disconnect the 2 element power wires. remove element. to install, reverse these instructions

First of all, let me say how "Not Handy" I am when it comes to these things. I decided to give this part a try after my oven decided to fail on Thanksgiving Day, so I ordered the part. It arrived on time as promised and packaged very well. The on-line parts breakout and testimony from the other buyers were so helpful. I had our oven back up and running in less than 10 minutes.

One thing I would also recommend is that you burn the element once installed for at least 15 minutes to get the newness smell off of it and then it won't permeate your food items.

Thanks, Parts Select! You saved me over $900.00; the price it was going to cost me to buy a new oven. :)

removed the two screws in the rear of the oven to access the element. once exposed I removed the four screws holding the element in place. Went to the ouitside back of the stove and removed one screw holding the shield to access the terminals for the element. Installation was in reverse order.

First I removed the oven door, then I removed the three screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then I connected the two wires to the new element , replaced the three holding screws and the oven door. ------END-------

The bake element in this oven is covered by a tray but after locating the screws for that and removing I could see the element was burnt so I just removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) then just reversed the procedure to install. Don't forget to unplug the unit first.

Turn of power to the range. The element lies beneath a metal cover. The cover is held down by two screws in each of the back cornors. The burner element is held by a screw in the the back and by two screws near the front. Replacing the element was a snap. With the screws removed, pull on the element until the connecting wires are exposed. Pull the wires from the element and attatch to new element. Replace screws, cover etc. Turn on power and note the time it takes to reach a preset temp. You may detect a slight oder form a coating on the new element. .

It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.

It took a view months, but well wort waiting for. My Stove is complete again, and I am very happy. Thank you for all your help.

The old part, including lightbulb and socket, had corroded into place, and the glass light cover was stuck to the socket. I used a dead blow hammer and a dowel just under the diameter of the hole to tap on the back side of the socket to loosen it and get it out. The metal tabs on the old socket were folded back to make it fit better (?), which made it harder to remove. Lots of muscling of the part to get it out. Easy to install new part once old one was out of the way. An experienced person would have removed the old part and installed the new in no time.

I trouble shot and traced out to electrical short in face panel and found burnt wires. I've been a licensed electrician for years and it takes alot of comon sense to trouble shoot and find problem. I found schetch-matic of appliance and searched computor and found partselect.com and tried it. It wasnt no time and the part was at my door. Thank you partselect and i would use them again in the future. billy

I received my glass panel realy quick from Part Select. It was an eansy job to install the new pane.
It took less than an hour. Thanks for Your prompt service.