MER7664XW2 Maytag Range - Instructions

It took a view months, but well wort waiting for. My Stove is complete again, and I am very happy. Thank you for all your help.

I order the part here, the first part never arrived, it was an empty package, the second part was breaking, the glass support was missing. Broken from the vent trim, then I was tired of it so I just put back the original broken part with some super glue on it, lol

Just follow included instructions.

Removed the ifinite controlswitch and replaced it but i dont believe it is wired correctly. now it wont get hot until it is set on four or so. think i the way it is wired.

I found on youtube Also we marked each wire with masking tape 1A and 1B, 2A and 2B. The wires were the same color.

Removed cooktop, wiring and coil. Marked where wires went on limiter
tabs. Ordered coil 1200 Watt, received a 1500 one. Sent back to PS with prepaid shipping label {great}. New one had a different limiter tab arrangement. The instructions included warned this but doesn't tell you where to put the wiring. Instructions say to remove the old limiter and put it on the new coil but this can not be physically be done plus who would want an old limiter on a new coil.
Found a YOU TUBE video on how to test and place wires on limiter switches which shows the number letter sequence on the ceramic part. Maybe PS will put that info in their instructions. Coil works great !!

Our repair was extrodinarily easy. As my husband was taking out the old element and the oven was off, the element heated up and actually burned him. He readjusted it and it refused to heat again. We figured at that point that there must be a short, so we never even opened the box with the new element. A short time later we decided to use the top of the stove for soup and a small fire started in the oven. We turned off the braker at that point and ordered a new oven.

very expensive to buy the part but just tighten the screw intot eh predefined place.

Remove 2 screws inside oven holding element . Remove screws holding back panel. Plug wires (2) into new element.Install back panel . Done.

Access to burner nothing like on-line videos:

1) Remove 4 screws under front control panel. (Oven door needs to be open.)
2) Remove 2 flat head screws on sides of control panel. This will loosen control panel. Capture control panel to keep from hanging from wires/connectors. I used hooks made from a wire hanger.
3) Remove 2 screws to remove two steel panels on either side of stove.
4) Remove rear screw of the 2 front screws now exposed and 2 rear screws near top of stove.
5) Carefully flip over glass top being careful not to pull on the wires.
6) Identify burner to be replaced. Note 2 numbers where two clamps are attached to burner.
7) Using 3/8” nut driver, remove screws to allow removal of burner. Remove wires per included instructions. Remove burner.
8) Place new burner under clamps and align to the holes by the two numbers noted in step 6 above.
9) Connect wires to new burner as per included instructions.
10) Reverse removal steps.

very easy watched the howto you gave

Went well. Husband, who has some appliance repair experience, did repair in less than a hour. Replacement burner was not an exact duplicate of original but he was able to adjust for that.

Unplugged stove.
Pulled stove out.
Unscrewed screws and removed cover.
Removed & replaced sensor.
Reinstalled cover & screws.
Plugged in stove and pushed back in.
Only problem was when I pulled stove out, lid opened and disconnected the gas line to a burner.

Removed 3 screws holding the glass door bracket.
Placed glass into door holders, had another person hold glass while I replaced the removable bracket screws.

just needed clearner for the top of my glass top, the operator was very helpful I received my clearniner in 7 days thank you