MER7765WB0 Maytag Range - Instructions

Yes... it exploded. Ordered the part which was delivered promptly. Installed in about 30 minutes with a helper. Just unscrew the 4 interior screws and a bunch of the screws (10 maybe?) on the back panel. Drop the back panel, remove the electrical connections from the broiler element and have your helper pull it out. Shove the new one in carefully through the insulation, attach the two electrical connections and reattach all the screws. Worked fine but smelled a bit as it burned off the new coating. About a 30 minute project.

Undid one screw. Removed the broken slide. Replaced with new slide an fastened with the existing screw. Problem solved.

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

First, I turned the circuit breaker off to the range. Then, I pulled the range out so that I could get to the screws which held the glass top in place. They were located on the sides of the range. I had to remove the trim pieces on the sides to get to the forward screws. Once that was done, I lifted the glass top, unplugged the wire harness, flpped it over on a protected surface. I noted the numbers on the old coil where the clips held it in place and put the clips on the new coil in the same place. The old wires just clipped on to the new coil exactly as they clipped on to the old coil. I put it all back together and it works great! I am a 70 year old woman who did this all by myself. You young guys should have no problem.

It's easier with two people.
1 - Turn the breaker for the range to OFF
2 - Verify power is off by testing the burners and lights
3 - Remove front two screws above oven door jamb
4 - Lift the top and prop it up with the spoon, or have your helper hold it.
5 - Loosen the screw at the rear of the bracket that holds the elements against the glass top (front and rear are held by the same retainer)
6 - Remove the bad element by sliding it sideways from the retainer. Do not disconnect things yet.
7 - The burner has numbers around the edge. Move brackets from old element to new one, matching the numbers. Then move wiring to new element. New burner may have a single connector where old one had 2 and a jumper. If so, ignore jumper.
8 - Slide new element under bracket and reinstall the screw.
9 - Lower the range top and re-install the screws.
10 - Turn on power and test.

OMG you have no idea how grateful I am. My husband and I watched your how-to-video and decided that it looked pretty easy for us to replace on our own. We saved close to $200 between the flat fee for a service call plus labor. Thank you very much. We were also pleased how fast our part was shipped to us.

This was very straight forward. Once the sheet metal shroud on the back side was removed just had to undo the one remaining wire, remove the block, and reassemble. Only question I had was which wires went where. The Wiring Block was melted due to the short and the wires were no longer attached. Did a quick google for a typical oven three-wire install and that did the trick.

Shut off 220 volt power to range. Removed two screws for cooktop element access. Used needle-nose pliers to remove power (2) and control (2) lugs and wires. Remove defective cooking element module, replaced. Reverse steps for new unit.

I unplugged the stove and removed two screws on bottom of stove top (above oven door) one screw holding burner bracket in place. Took one wire off at a time and hooked to new burner, tightened all screws back down.

Turn off the breaker to the range. Unplug, too. Took off the 8 screws that hold the upper back panel on. Took a picture of the wire setup (this ain't my first rodeo). Removed two screws on the bottom of the old latch that hold it in place. Carefully removed the wire leads with needle-nose pliers because I didn't want to replace the wire leads. Reconnected the wires to the new latch, replaced the two screws to hold it onto the oven. Tested with the rocker switch on top and the oven door, both worked. Put the back panel on with the 8 screws.

Contrary to instructions(go thru front of oven) I had to pull out the range, remove two (2) screws from back chassis. At this point you pull out the connector, snap in new, reverse proceedure. Very simple. Hardest part is cleaning up debris generated by moving range.