MER7662WT0 Maytag Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Diane from Elyria, OH
- Parts Used:
- WP8523175
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The original trim rusted
I did the repair by myself. I used masking tape to hold the side trim in place. It was pretty easy and it looks great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louise from Humansville, MO
- Parts Used:
- WP9761958
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Terminal Block was melted where the cord had came lose.
Removed the therminal block and put the new one in.Using a screwdriver, very easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gene from Turtle Lake, ND
- Parts Used:
- W11171119
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burned out stove top burner
Easy change! Two screws in front and grounding strap screw-lifted out and turned stove top upside down on table. three more screws for burner element and then reinstall with first two screws and grounding strap screw.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Ft Myers, FL
- Parts Used:
- WPW10118454, WP8523175
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Glass door front fell out during cleaning and shattered
Install bottom door trim first...Remove upper door handle and set new glass door front piece in place and re install upper door handle and tighten all screws...Looks great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Oceanside, CA
- Parts Used:
- W11594027
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Damaged Socket When Removing Bulb Base
This is a built-in oven, so the biggest problem was figuring out how to remove it from the cabinet. The solution turned out to be removing the cooktop above it and unscrewing two screws that connected the oven to the inside of the cabinet. The other problem was removing BOTH metal backs from the oven. The first one was easy. The second one wasn't. The old socket was recessed behind the second back, making it virtually impossible to access the metal "wings" that hold it in place, so I ended up pulling out the socket assembly from inside the oven with pliers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amadeusz from Simi Valley, CA
- Parts Used:
- W10856603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Broil heater exploded. The corner was burned/ corroded.
Unplug power. Remove panel on the back. Unplug heater.From front remove 3 screws and remove heater. Installed new heater. On the back restored connections - squized the lugs to have better connection. Put panel back. Plug the power and see if the coil get red. It looked good. Used oven few times it works fine. Difficoult part is to clean oven all around from accumulated grease. First repair for this stove, most of the time spend on figuring out what to open, no instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rodney from Columbus, OH
- Parts Used:
- W10856603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
broiler didn't work
Removed original broiler element, and found it was open. Replaced with new element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Mauldin, SC
- Parts Used:
- WP8053334
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rear drawer slide was broken.
Undid one screw. Removed the broken slide. Replaced with new slide an fastened with the existing screw. Problem solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thaddeus from Washington, DC
- Parts Used:
- WPW10118454
- Difficulty Level:
- Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broken outer range door glass
Using 4 strips of duct tape was useful,in holding the glass to the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Grant from Alexandria, VA
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light bulb failure
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- karen from Thornton, CO
- Parts Used:
- WP8053334
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken drawer glide
Used a phillips head screwdriver to remove the single screw holding the part in place and put the new one on. Finding the part on this site was a breeze and it arrived quickly. A first rate experience all around.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alfred from Ann Arbor, MI
- Parts Used:
- WP3149404
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Left front 8 inch burner knob control stop regulating heat temprature.
I purchased a new infinite control switch 6". and replace the old one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Lewisville, NC
- Parts Used:
- WP3149404
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element would not get red hot
Replaced Infinite control switch in just a few minutes. Unfortunately the new switch had a lose terminal that was not supposed to be in the switch that came from the factory that way. I connected the switch, turned it on, and it instantly shorted the switch out. At that point the lose terminal was real easy to see.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from kissimmee, FL
- Parts Used:
- W10856603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
top element was burnt out small burn hole in element
removed the screws that were on back side of oven securing panel that covered element terminals disconnected wiring to upper element then went in side oven area removing 4 upper mount screws that were holding upper element in place then removed old element and reinstalled new in same order was removed..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Roberts, MT
- Parts Used:
- WP9761958
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Wiring Block shorted due to moisture and Stove had no Power
This was very straight forward. Once the sheet metal shroud on the back side was removed just had to undo the one remaining wire, remove the block, and reassemble. Only question I had was which wires went where. The Wiring Block was melted due to the short and the wires were no longer attached. Did a quick google for a typical oven three-wire install and that did the trick.
Was this instruction helpful to you?
Thank you for voting!