MGR5765QDQ2 Maytag Range - Instructions

took out racks removed 2 screws holding igniter removed 4 screws on back of stove and unplug igniter. reversed the order installing the new one

Took the bottom out of oven then removed and replaced with the new part. VERY EASY! I'm a 70-year-old woman and do quite a few home repairs myself.

1. Turn power off and loosen and remove screws. Pull out sensor from mounting hole and expose wire connector. Remove old sensor. Select appropriate wire adaptor and reconnect the sensor. Carefully push connector through hole and secure with screws removed previously. Turn power back on and cycle oven to make sure oven operates properly. If you have an oven thermometer it can be used to compare set point of oven to thermometer to make sure readings are the same. All done! Happy wife can now bake cookies again and now I can go back to man cave for other projects!

pulled the old gasket, the new one fitted perfectly. No effort at all.
An instruction sheet would be a bonus. I wish you put instruction sheet in all parts OR a web link for video instructions. a web link would be great

Removed old assembly, attached wires to new and inserted into space for same. Of course you must turn off the range circuit breaker. The part that took the most time was removing the old assembly. Once that was done, the rest took only a few minutes.

Removed oven door, removed bottom of oven, removed old igniter, installed the new one and plugged it in in the back of the stove. Installed oven door and it works fine. .

It was easy to remove the old oven door gasket. Just a little tug was all that was needed. Installing new gasket was just as simple as tucking in the gasket end into the hole at the bottom and pushing the clip in the corresponding hole.
TIP: roll the end of the gasket and feed into the hole then use a small tipped screw driver or the point of a needle nose plier to finish installing the ends into the hole at the bottom of the door opening.

replaced heat sensor

We removed the door from the hinges by sliding it up. Then we removed all the screws holding the door together. We had to remove the screw securing the trim. Next we removed the screws inside the trim holding the old handle. We replaced the handle and trim and screws in reverse order. Finally, we re-attached the door by sliding it onto the hinges.

The best I can say is to remove door. take screws out from the bottom and sides first. Clean all layers of glass before installing handle.

I removed all the screws that held the trim and inner frame to the outside window unit first. Then, I removed a protective glass from over the two inner panes. Next after removing the frame that held the two inner glass panes together, I took the broken inner glass pane out and replaced it with the new one. Then basically I just retraced my steps and had the door put back together in about 45 minutes. You just need to pay close attention to your disassembly so that you are able to put the pieces back together quickly.

Removed 3 Phillips head screws at top of oven door. Tipped this top casing back just enough to remove glass door panel. Removed door mounting brackets from door (phillips). Removed end of handle from attached end of frame piece. New handle screw stubs changed from original to need self tapping screws (with washers), so had to find appropriate screws on my own (screws sent to me for new handle were straight machine screws as needed with original, broken handle). Found self tapping screws and washers, screwed new handle to brackets, screwed brackets to door panel, loosely screwed 3 top frame screws, tipped top frame back enough to reinstall glass door front, screwed down 3 top frame screws and it was done.

I located the temp sensor (top left). Removed the 2x Phillips screws and slide the wire out until the plug is thru the opening taking care not to pull to hard as to damage the end that you not going to replace. To install plug it in and push the wire thru and secure with 2x Phillip screws.

Oven and broiler have two seperate igniters. Broiler worked but oven did not heat. Oven igniter located under metal pan at base of inside of oven. remove pan by lifting, and remove completely from oven. Igniter under this pan and held in place by two srews. Remove screws, unplug from cable, replug in ne igniter, replace two srcews and pan, and you're done! this part cost about $50 and I installed, last time Sear replaced =$300.

Door was removed very easily. Outside trim pieces were removed. The rest came apart like a simple puzzle. Inside glass is very easily accessed. Upon assembling, time was well under an hour. Shipping was fantastic and I saved close to 200dollars between a service call and a repair.