MGRH451BDW Maytag Range - Instructions

I needed to remove the rear panel to replace the sensor, but unfortunately, that was not the problem. It could have been; but also, it could have been the electronic control, or the gas control valve. This was the cheapest "trial" fix. I did talk to a "Warranty Repair Man", who said that IF it was the electronic control, because of the age of the oven, (13 years) the part would not be available and would need to be fabricated by the manufacture. Even then the cost would approach the cost of a new oven. So, we abandonded the idea of repairs to this one. I guess 13 years is a bit to much to expect of a machine this day and time. Things are made to use-up and throw away. Such is life ! !

igniter would heat but oven wouldnt come on or would intermittently.opened door a little and lifted it off removed racks and bottom shield removed wingnut and burner shield,removed 2 screws holding igniter ,took off lower shield to allow access to plug,unplugged old one plugged in new one replaced shield and 2 screws holding igniter,put oven back together in reverse order,works like new :) ps if unit not unplugged from wall be careful igniter is hot with electricity and will bite you OUCH!

Removed the old burners with a Plumbing Pipe Wrench by turning 1/4 turn counter clockwise. Disconnected (2) wires and replaced with new Sealed Burners. The simmer burner wires were slightly diffrent from the original but they do fit by opening the connector with screwdriver and then clamping once wire inserted.

replaced grates

Even though the ceramic insulator looked new (white), it had become non-functional, replacement was simple, 2 phillips screws, reassemble and test. Now I will have to order the other 3.

0. Throw oven circuit breaker 1. Open oven door and slide/lift door off of hinge posts 2. Remove oven drawer 3. Slide oven out from between cabinets and turn so that the back is accessible. 4. remove Phillips screws holding the cover-rear and side panel to the stove. Note which screws have pan heads and which are hex head. 5. remove stove elements and pans 6. Raise stove Top Assembly and release ceramic element sockets from their clips. 7. Push the supports for the Top Assembly fornt and back to release them from their sockets so that the Top Assembly can be lifted to near vertical. 8. Remove the hex head screw holding the Control Panel End Cap to the side panel. (Steps 5-7 might be avoided if you have a small socket wrench that can get to this screw without removing the elements.) 9. Remove the other screws holding the top of the side panel to the "Box Burner" pan that sits under the Top Assembly. 10. Pull side panel slightly away from the oven and lift it to disconnect it from the posts that hold the side panel to the front of the oven. 11. Remove the two screws on the front of the oven that hold the hing mechanism. 12. tilt and remove the hinge. 13. Open the replacement hinge so that it can fit through the hinge opening in the front of the oven. 14. Reassemble.

First I changed the temperature sensor and when it didn’t get hot I Also changed the igniter. Fired right up.

I didn't. Don't know how to get to light bulb to change it for this specific model

I first matched the symptom (very long preheat time/gas odor) with the most likely problem (faulty oven gas igniter). I then wrote the model # and Googled gas oven repair and got to your website. I then located the faulty part within about 5 clicks and proceeded to order the exact part within another 5 or so clicks. I received my order from PartSelest in 2 days and had the oven working with the new igniter in about 10 minutes....Then it dawned on me---"Hey, I should be a Maytag Repair Man."
Thanks for the prompt delivery and the correct installation instructions. I will absolutely use your service again. (Not too soon, I hope !)

Removed the drawer and the flash plate underneath .
Unplugged the igniter then opened the & removed the over door . Lifted the bottom plate to expose the burner and igniter . Undo the 2 screws holding the igniter in place . Replace the igniter and reach underneath and plug the wire connecters together . Place all the proper things in their place .. and it was finished ...
The biggest snag I ran into was the one of the 2 screws stripped out when when taken things apart .. but I have taps and found a few new screws and replaced them ......
Quite easy fix .. don't a pay repair man to do it .... !!

moved stove away from the wall, Disconnected power, Removed 2 screws on the access panel and removed panel. Disconnected qwick release conections on heat sensor and ignitor, Removed oven door and burner cover to expose ignitor, removed 2 screws to remove ignitor and replaced ignitor. Removed 2 screws and removed sensor, replaced sensor. Reconnected qwick conects on sensor and ignitor. Replaced oven door, burner cover and access panel and checked out. Checks OK !

So simple! I really had no idea what the problem was. I found the PartsSelect site, read the comments from fellow Maytag double oven owners, diagnosed the problem as the sensor and ordered the part. It arrived in only two days! We removed the back of the stove, pulled the old sensor through, plugged the new one in and YAY the oven is like new. I have to admit most of the repair time involved sweeping up the dog hair that had accumulated under the stove.

slide out stove remove rear cover (6 screws) to access sensor plug . remove two screws from inside oven area and remove part,replace in reverse order.

Unplugged the stove and unscrew the 2 screws on the thermometer inside the stove and unplugged the white plastic in the back of the stove and I had to put the new extra piece that came with the sensor kit as it was needed because the socket were different.

The flame holder twists about 1/2 inch to left and lifts off. I removed the two screws that holds the igniter on and removed it and installed the new igniter.
There was one complication: when I put it back together, there was no spark. I removed the ground wire and cleaned and scraped it and replaced it and still no spark. But, for no apparent reason the spark returned and has been okay since.