MGRH865QDS0 Maytag Range - Instructions

Remove oven door, pan drawer, oven racks, bottom pan, flame spreader. Remove valve cover at back of pan drawer. Unplug old igniter. Remove two mounting screws holding igniter to gas tube assembly. Install new igniter, plug it in, and reassemble. Easy as pie! Oven works better than it has for a looooong time! Heats up to 400 in 5 minutes. Wife is happy! :)

I shut the gas off and removed the oven door pulled the oven out and removed the electrical access panel.
unpluged the igniter and removed the 2 screws holding the igniter and relpaced repluged.
right to self clean mode. Easy job no worrys
Be safe check your gas connection!!

Nothing to it - remove oven bottom, and burner cover, unscrew the 2 scews holding the igniter
(one of mine sheared off now only one is holding the new igniter in - it still works) unplug wire at the connector then reverse and the oven is as good as new. The best part is that I received my part in only 2 days.

First I removed the bottom plate in the oven. The ignitor was located at the rear of the burner and I removed to screws and it was loose except for the two wires. Next I removed the bottom tray from the stove. Two screws held the metal guard in place at the rear of the stove. After removing the plate, I determined which wires belonged to the ignitor, unplugged them at the coupling and pulled the wires out through the bottom of the oven. Replacing the ignitor was simply to reverse the proceedure. PartSelect got the part right out to me, installing the new part was a breeze, and my wife calls me her "hero." This site was a real help and saved me a service/repair bill. Thanks!
Fred

I turned off the gas at the back of the oven & unpluged it. I then removed the 2 screws that secure the oven bottom plate to the oven. Once removed, that exposes the oven burner & igniter. There are 2 sscrews that secure the igniter to the burner; remove those screws, & pull the igniter wires out, to expose the connector. Unplug the connector, & the igniter is free. Just reverse the process with the new igniter.

removed door (no tools required - just lift and pull door out of range). removed front door panel with a screwdriver. removed/replaced door hinge with nutdriver. replaced front door panel with screwdriver. replaced door on range (again, no tools required). then installed tip-over bracket to floor/wall behind range. measured location, drilled pilot holes and installed wood screws into the floor and rear wall stud.

Remove two screws back panel and remove sensor two screws inside top oven.

I first tested the broiler and that worked so we determined that the igniter on the bottom was not working. I removed the grill and then removed the igniter ( it is attached with two screws and unplugs from the back of the oven. I then looked up the part we needed on the part select website by model number and found the exact one ( the picture was very helpful) We received the part in one day installed it and the oven is working better than ever.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Plug in the element put the wires back in the hole and screws the element on and that was it. Worked great.

Open oven door remove trays.. remove floor of oven...remove single screw holding heat shield... unscrew two srews holding ignitor and unclip plastic...done..reverse to install

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

We took the interior floor out, pulled the stove away from counter, before that turned all electricity to the house off. Then we unscrewed the ignitor inside then underneath unplugged it and plugged in the new one, cleaned to oven and screwed the ignitor in and replaced the interior floor and we were done.

Replaced gas oven ignitor

seamed easy enough. Found the part and it looked identical, However I could not see the connector in the picture because the logo covered that part of the picture. Had to cut the connector off the old igniter and crimp it on to the new ingniter.

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.