MER6875BAB17 Maytag Range - Instructions

I removed all the screws that held the trim and inner frame to the outside window unit first. Then, I removed a protective glass from over the two inner panes. Next after removing the frame that held the two inner glass panes together, I took the broken inner glass pane out and replaced it with the new one. Then basically I just retraced my steps and had the door put back together in about 45 minutes. You just need to pay close attention to your disassembly so that you are able to put the pieces back together quickly.

The best I can say is to remove door. take screws out from the bottom and sides first. Clean all layers of glass before installing handle.

Oven sensor replacement was easy. Thermistor was installed in less than 15 minutes. After installation STILL had "F3" error message. Harness was ok, "Clock" or ECU needed to be replaced. "Computer" is obsolete, no spares available, some companies will rebuilt for $400+. Since the stove was going to the landfill I had nothing to lose by taking the "Clock" apart. It has one chip that is probably the power supply and control chip, another chip is an EEPROM with 128 bytes of storage and the last is a darlington chip that controls the relays. Cleaned up everything that looked like it needed cleaning with alcohol. When I reassembled the unit the pins for the thermistor harness felt loose, so I took it apart, again, and found cold solder joints on all four pins. It must have been there all along but plugging and unplugging the harness finally broke out the solder so I could see it. Soldered the pins back in and now it all works. It's worth a try if you're getting the "F3" message. If the relays on your stove aren't working it would be a good idea to replace the darlington chip. Good luck.

Remove the door.
Remove screws
Clear out broken glass. Vacuum out small glass shards.
Clean all glass.
Reattach all parts.
Replace the door.
Smile!

Door was removed very easily. Outside trim pieces were removed. The rest came apart like a simple puzzle. Inside glass is very easily accessed. Upon assembling, time was well under an hour. Shipping was fantastic and I saved close to 200dollars between a service call and a repair.

Removed two retaining screws and pulled out coil. one terminal came off readily but one remained and was difficult to get off. Pulled range out from wall and removed cover plate and removed existing terminal connection. Pushed new coil into oven openings and screwed in. Slide terminals on in the rear of range and replaced cover plate. Took about 1/2 hour because I was nervous.

Watch the video. Spot on instructions. Easy peasy.

Spoke to your very helpful staff, who advised me that a likely problem was the oven sensor. I took a chance and ordered the part, which came promptly. Your service video for the part was most helpful in my decision to try the part. Installation was a breeze, but it was the oven controller board that had failed and not the oven sensor. That called for a service professional, who ultimately fixed the problem. Your service though, was excellent and I would highly recommend you to others.

Two Screws on the back. Pull out heating element and remove wires. Install new wires and replace screws. Done in 5 minutes

I switched the oven sensor easily enough, but it did not remedy the problem, so we are in the process of replacing the oven since it's about 20 yrs. old.

I took the door off and removed five phillip screws from the old bottom support and removed it. I took the opportunity to clean the glass on the front and back before placing it back on. It simply fits into two keepers at top and is held on by the new support at the bottom. I replaced the five screws and put the door back on. It is a simple job that only takes a few minutes.

pull oven out and Un-plug oven remove screws from back panel , un plug wires from old heating element. open oven door and remove the two screws that was holding the the old heating element, pull it out . Install the new heating element and replace screw. plug wires to the heating element in the back of oven. Replace back panel. plug oven back in. and test

I shut off the breaker to the stove. I removed 2 screws from the underside of the cooktop at the front of the unit. I raised the cooktop and had my helper hold the top at an angle to access the burner. I removed 2 screws attached to the burner and then loosened the 2 clips and moved them to release the burner. I transferred the electrical connections from the old to the new. Reinstalled the burner and cooktop. Turned the breaker on, tested the new burner and I was fone

IMPORTANT NOTE: This element is shaped like a B. The straight line part of the B, which is closest to the back part of the oven, doesn't light up. At first I thought it was a defective part. My husband is the cook and I never realized this. This fact isn't indicated in the instruction booklet which came with the oven. My sister has the same oven and she didn't realize it doesn't light up either. I looked up installation instructions on You Tube and although I was very nervous, it was easy to install. It's a little awkward because the wires are in the back of the oven so have a flashlight handy.

First I called a repairman and left a message. That was 3 weeks ago. So, I 'googled' the error message and determined what part I thought I needed. Ordered the part on Wednesday evening and it was there when I got home from work on Friday. I unpacked the part, got a phillips screwdriver and then watched the repair video on your website. About 20 minutes later I pushed my stove back in place and the flashing said 'set time'. Then I checked both ovens, and have since used both, and everything works!!