MER7662WS0 Maytag Range - Instructions

Take off the back panel of stove and unplugged timer motor and switch on door latch assembly,removed two screws that hold assembly and slide rod off. I put 110 volt plug to timer motor and it did not move, that is how I diagnosed problem. Ordered new assembly (cannot buy just timer motor)put new door latch assembly on and worked fine. Of course unplug stove before you start !

just replaced the broken glides with the new ones.

turn the light on in the oven go to the breaker box and shut off power to the oven when light is out is good indicator remove two screws in back of oven that secure element to back then remove two screws on top inside the oven to almost finish removal. phillips head screwdriver and needle nose pliers and two small spring loaded clamps are all you will need to accomplish thismove the upper element side to side until the connectors are exposed in the back of the stove pull the two wires out about 4 inches should be enough place the spring loaded clamps on each wire so as to not allow them to slip back in the stove body. take the needle nose and while holding the clamp remove the connector from each wire once this is done place the new element in the stove and reconnect the clips on the end off the element move the wires and connectors back into the openings on the stove and replace the two screws replace the two upper screws check all screws for tightness go to the breaker box and turn on the power takes about thirty minutes

changing the part itself was easy, but the sheet metal covering the whole back of the oven was difficult to remove because of some screws that were stripped. The new sensor solved the problem.

Yes... it exploded. Ordered the part which was delivered promptly. Installed in about 30 minutes with a helper. Just unscrew the 4 interior screws and a bunch of the screws (10 maybe?) on the back panel. Drop the back panel, remove the electrical connections from the broiler element and have your helper pull it out. Shove the new one in carefully through the insulation, attach the two electrical connections and reattach all the screws. Worked fine but smelled a bit as it burned off the new coating. About a 30 minute project.

We called a dear handyman church member with years of repair service to his home, personal vehicles and general maintenance of our little church and parsonage. Known for his trade as an engineer with over 50 years in the industry wearing white shirts and working in an office; however, he is not afraid to get his hand dirty. We all worked together (my husband, daughter and me) to troubleshoot and resolve the problem and the terminal block purchased from "parts select" was just the answer to all our problems and worries. The range is fully operational and works like new. Thanks.

I remove bottom trim which is held on by 3 screws and try to install new bottom trim, did not work well. I then remove yop handle assem. Then the door glass which you need to clean after. Then install the new bottom trim then insert the glass into the new bottom strip using masking tape to hold the glass and side strips in place prior to installing the the top handle piece which is held on by two screws. Not a hard job to do.

This is a built-in oven, so the biggest problem was figuring out how to remove it from the cabinet. The solution turned out to be removing the cooktop above it and unscrewing two screws that connected the oven to the inside of the cabinet. The other problem was removing BOTH metal backs from the oven. The first one was easy. The second one wasn't. The old socket was recessed behind the second back, making it virtually impossible to access the metal "wings" that hold it in place, so I ended up pulling out the socket assembly from inside the oven with pliers.

Unplug power. Remove panel on the back. Unplug heater.From front remove 3 screws and remove heater. Installed new heater. On the back restored connections - squized the lugs to have better connection. Put panel back. Plug the power and see if the coil get red. It looked good. Used oven few times it works fine. Difficoult part is to clean oven all around from accumulated grease. First repair for this stove, most of the time spend on figuring out what to open, no instructions.

I did the repair by myself. I used masking tape to hold the side trim in place. It was pretty easy and it looks great.

Removed the therminal block and put the new one in.Using a screwdriver, very easy repair.

Easy change! Two screws in front and grounding strap screw-lifted out and turned stove top upside down on table. three more screws for burner element and then reinstall with first two screws and grounding strap screw.

Install bottom door trim first...Remove upper door handle and set new glass door front piece in place and re install upper door handle and tighten all screws...Looks great

Removed original broiler element, and found it was open. Replaced with new element.

Undid one screw. Removed the broken slide. Replaced with new slide an fastened with the existing screw. Problem solved.