MER6755ACB24 Maytag Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Howard from Ticonderoga, NY
- Parts Used:
- WP74011767
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
handle broke on one side
The best I can say is to remove door. take screws out from the bottom and sides first. Clean all layers of glass before installing handle.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- phillip from Farmington, NM
- Parts Used:
- 12001656
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers
Maytag range had "F3" code display, oven would not work.
Oven sensor replacement was easy. Thermistor was installed in less than 15 minutes. After installation STILL had "F3" error message. Harness was ok, "Clock" or ECU needed to be replaced. "Computer" is obsolete, no spares available, some companies will rebuilt for $400+. Since the stove was going to the landfill I had nothing to lose by taking the "Clock" apart. It has one chip that is probably the power supply and control chip, another chip is an EEPROM with 128 bytes of storage and the last is a darlington chip that controls the relays. Cleaned up everything that looked like it needed cleaning with alcohol. When I reassembled the unit the pins for the thermistor harness felt loose, so I took it apart, again, and found cold solder joints on all four pins. It must have been there all along but plugging and unplugging the harness finally broke out the solder so I could see it. Soldered the pins back in and now it all works. It's worth a try if you're getting the "F3" message. If the relays on your stove aren't working it would be a good idea to replace the darlington chip. Good luck.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from WOODSTOCK, OH
- Parts Used:
- WPW10187838
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Burner element replacement
Took out 2 screws along the underside of the glass top. Unhooked the glass top from the back of the range lifted it up and supported it with a board. Removed 2 screws holding the old burner in place and lowered it down onto the insulation on top of the oven. Removed the wires and reattached them in order to the new burner. Removed the screws holding the brackets to the old burner and attached them in the same places on the new burner. Reattached the burner to the bottom of the glass top the placed the glass top back in its proper position and put the 2 screws back in holding it in place. Plugged in the range and tested the burner to make sure it worked. Then slid the range back into position. All done in about 30 mins. Not very difficult at all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leslie from HARVEY, IL
- Parts Used:
- WP74011767, WP74006515
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
handle on oven door broken on one side
once I figured out how to remove door it was a piece of cake for a 72 year old man.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- pamela from MONROE, WA
- Parts Used:
- 74003645
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Inner oven door glass cracked.
Watch the video. Spot on instructions. Easy peasy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from East Sandwich, MA
- Parts Used:
- 74003645
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Shattered inside glass when attempted to self-clean
Door was removed very easily. Outside trim pieces were removed. The rest came apart like a simple puzzle. Inside glass is very easily accessed. Upon assembling, time was well under an hour. Shipping was fantastic and I saved close to 200dollars between a service call and a repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dale from SAINT PETERS, MO
- Parts Used:
- WP7403P239-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Front 8" burner stuck on high no matter where dial was set.
This range was easy. Only 4 screws under the front panel that allows the panel to come off. No need to pull the range out for back screws.
Replacement part was exact and worked perfect.
Turn off the circuit breaker for the range.
Remove the 4 screws under the front panel, one on each end and one one each side of the display/control panel.
Pull the bottom of the front panel out about 30 degrees and lift off the top.
Once panel is off pull of the dial knob, remove the two screws for the control and swap wires on at a time with the new one.. Reverse the procedure and all is good. You may need to use needle nosed pliers on the spade connectors if they are too tight to pull off by hand.
Replacement part was exact and worked perfect.
Turn off the circuit breaker for the range.
Remove the 4 screws under the front panel, one on each end and one one each side of the display/control panel.
Pull the bottom of the front panel out about 30 degrees and lift off the top.
Once panel is off pull of the dial knob, remove the two screws for the control and swap wires on at a time with the new one.. Reverse the procedure and all is good. You may need to use needle nosed pliers on the spade connectors if they are too tight to pull off by hand.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerome from RICHFIELD, MN
- Parts Used:
- 74003645
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Broken inner glass window.
Remove the door.
Remove screws
Clear out broken glass. Vacuum out small glass shards.
Clean all glass.
Reattach all parts.
Replace the door.
Smile!
Remove screws
Clear out broken glass. Vacuum out small glass shards.
Clean all glass.
Reattach all parts.
Replace the door.
Smile!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melissa from MANCHESTER, NH
- Parts Used:
- WP7406P428-60
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Lower heating element brunt out
1) unplugged stove, 2) opened oven door, 3) removed racks, 4) Unscrewed heat element plate, 5) removed broken heat element, 6) connected new heat element, 7) re screwed in the plate, 8) plugged stove in, 9) turned oven on to verify new heat element was working, 10) placed rack back in oven. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from SAINT MARYS, KS
- Parts Used:
- 12001656
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven would over heat and produce a F2 error code on the display. It would not turn off or cool down until I switched the circuit breaker off.
I switched the oven sensor easily enough, but it did not remedy the problem, so we are in the process of replacing the oven since it's about 20 yrs. old.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from ABINGTON, MA
- Parts Used:
- WP7406P428-60
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Broken Heating Element
Two Screws on the back. Pull out heating element and remove wires. Install new wires and replace screws. Done in 5 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yafa (and David) from Bothell, WA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- francis from mount holley, VA
- Parts Used:
- 12001656
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven would not heat
Spoke to your very helpful staff, who advised me that a likely problem was the oven sensor. I took a chance and ordered the part, which came promptly. Your service video for the part was most helpful in my decision to try the part. Installation was a breeze, but it was the oven controller board that had failed and not the oven sensor. That called for a service professional, who ultimately fixed the problem. Your service though, was excellent and I would highly recommend you to others.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Georgene from Rock City, IL
- Parts Used:
- 12001656
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
After cleaning, F1-1 error flashed and neither oven worked
First I called a repairman and left a message. That was 3 weeks ago. So, I 'googled' the error message and determined what part I thought I needed. Ordered the part on Wednesday evening and it was there when I got home from work on Friday. I unpacked the part, got a phillips screwdriver and then watched the repair video on your website. About 20 minutes later I pushed my stove back in place and the flashing said 'set time'. Then I checked both ovens, and have since used both, and everything works!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from VIRGINIA BCH, VA
- Parts Used:
- WP7406P428-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lower element would not heat up
pull oven out and Un-plug oven remove screws from back panel , un plug wires from old heating element. open oven door and remove the two screws that was holding the the old heating element, pull it out . Install the new heating element and replace screw. plug wires to the heating element in the back of oven. Replace back panel. plug oven back in. and test
Was this instruction helpful to you?
Thank you for voting!