MER6757BAQ14 Maytag Range - Instructions

Turn off breaker in electric panel fore stove. Put screw driver into slots in front of glass top surface. Pry top up carefully until top pops up.Remove burner dial, remove two philips head screws holding switch. Lift top carefully and prop up.With new switch close remove wires from old switch one at a time and place on new switch. Place new switch back in place, securing with philips screws. Remove prop and carefully press top down until it snappes into place.Replace dial, turn breaker back on and try burner.

1. OPEN THE OVEN DOOR TO THE FIRST STOP,
PULL UPWARD TO REMOVE, ( IT WILL LIFT RIGHT
OFF)
2. LAY OVEN DOOR ON A FLAT SURFACE ( HANDLE
DOWN AND HANGING OFF SURFACE) WITH A
TOWEL TO PROTECT THE GLASS.
3. REMOVE ALL SCREWS AROUND THE
PERIMETER OF THE DOOR..
4. CAREFULLY SEPARATE THE DOOR FRONT AND
BOTTOM BRACKET BY SLIDING AWAY FROM
THE MAIN DOOR INNER-ASSEMBLY, ( THE
FRONT GLASS IS HELD BY THE TOP CHANNEL.
5. TURN THE MAIN DOOR INNER ASSEMBLY OVER
AND REMOVE THE HANDLE ASSEMBLY TWO
ATTACHING BRACKETS.
6. REMOVE THE ATTACHING BRACKETS FROM
THE HANDLE AND ATTACH TO THE NEW
HANDLE.
7. THE DOOR GLASSES CAN NOW BE CLEANED
8. ATTACH THE NEW HANDLE ASSEMBLY
9. REASSEMBLE IN REVERSE ORDER.
( BE CAREFUL WHEN SLIDING FRONT DOOR
GLASS INTO THE TOP DOOR CHANNEL}

Removed oven door and rack. Removed two screws holding element. Disconnected wires to element. One of the wires slipped into the back wall of the oven. The range had to be removed from the counter and back panel removed to gain access to the element wires. Install new bake element in upper oven. Connect wires to element spade lugs. Install rear panel. Restore power at circuit breaker panel. Very important - aways disconnect power before starting work.

Shut off power at breaker box , pull stove away from wall , remove Phillips screws from back of range pull knob off of switch . Look to see how switch is oriented remove 2 screws that hold switch in . Remove one set of wires at a time and place on new switch in same location . Put back together in reverse order .

turn off all electric to the wall oven. removed the old broiler. replaced the new broiler and turned on the electric. checked the brolier one to see if it worked....it did thanks for the customer service for her help in finding the replacement part.

I slide the range out and unplugged it from the outlet. I removed the back of the oven ( 8 screws ) using a cordless drill and phillips bit then with a phillips screwdriver I removed the oven sensor (2 screws) then I installed the new sensor , reinstalled the oven back , plugged the range in , slide it back into place and that was it. This repair took about 10 mins and the oven works perfectly. Thanks !

Waited for my husband to do it, but when he didn't, I tried it. Very simple! Just pulled the old gasket out of the pinch pin holes in the door, then replaced it. Tuck the one end into the hole at the bottom of the door, then match up the little pinch pins on the gasket with the holes in the door - matches up perfectly! Be sure to tuck in each of pinch pins till they sort of "snap" into each hole. Took me 5 minutes, tops. Works great now, no more lost heat around the edge of the door.

Removed door from oven by pulling up at the first stop point after opening the door. Removed the outer shell by removing 5 screws. Disassembled the inner door by removing 6 screws. Be careful with the insulation blanket (fits in a molded portion of the inner door). Glass windows can be removed (for cleaning) via a couple screws. Old gasket/seal is held in-place via spring-clips; just squeezed each clip, pushed each thru their respective holes, and pulled off the worn-out gasket. New gasket snapped in-place by pushing the clips thru the respective holes. Reverse the process to reassemble the door. You can do this job in 15-20 minutes. Took us longer because it took some elbow-grease (and patience) to clean the crud off the glass windows.

Removed the approximatly 10 screws that hold on both the upper and lower pieces of sheet metal that cover the back of the oven. Removed the screw holding in the temp sensor. Unplugged and removed the old sensor. Plugged in and installed the new sensor (using one of the included adapter wires supplied with the sensor). Put the 2 pieces of sheet metal back on and plugged in the oven.

Took the old levelling leg out and screw the new one in.

The first set of racks did not fit. I called the Service rep, gave him the model number and exchanged the racks for the new ones. The new ones fit perfectly and the service was excellent. I would definitely recommend PartSelect.com to anyone who wants to deal with a company with excellent service, parts and representatives who know their stuff.

When the element failed, it continued to glow nearly white-hot and slowly burned along a spiral path on the element. I figured this MUST be due to a voltage leak - the control was OFF on the range.

I shut off the breaker, removed the two screws where the element goes through the back of the oven, pulled the element forward and pulled the wires off of the element. (Found it handy to twist the wire connectors outward to prevent the wires from slipping through the back of the oven.)

A new element won't "fit" exactly but you can easily push it into position to get the screw holes to line up. Total time was less than 15 minutes.

From reading other reviews i thought I would have to dis-assemble the door but when I saw the new part I realized I would not have to, simply pop the beveled clips w/pocket knife and pop in the new seal clips. the ends tucked very nicely, an 80+ yr. old would have no trouble if they had their wits.

Remove the door, remove screws from all sides

Remove sides and face of oven door by sliding down from under the oven handle trim.

Remove screws on 2nd light of glass and set aside.

Now you are at the inner door panes. their should be two in an insulated type unit.

Remove the remaining screws from the handle pracket and the permiter frame for the glass/insulation. Remove permiter frame and set aside.

Pull out inner door glass frame. get a pair of pliers and bend tab on frame up so you can pull the frame sightly apart, replace the glass, secure frame tightly around glass slide tab back into reciever slot and bend down ( you may need another person to assist in keeping both lights in the frame while trying to ben tab back in to place)

reassemble door as it came apart carefull not to over tighten the screws, they strip easy.

removed screws and disconnected the wires removed element and did the replacement less than 15 minutes, and cost less than locally by 25.00 and received part the next day. EXCELLENT