MER5775RAB1 Maytag Range - Instructions

Be prepaired to take the glass out. Unexpected, but not too hard. A right angle screw driver can be helpful for the bottom door. Takes some skill and patience. Good Luck! I am happy with the parts. Delivery time was quick.

I wasn't sure if it was the heating element or the temperature probe not allowing the oven to go above 200 degrees so I ordered both from Selectparts. After receiving my replacement parts (in record time thank you) the oven element had a hidden slit on the underside near the connection. During its removal the element disintegrated at that point.

Since Maytag is very user friendly to maintain, it was a matter of removing the retaining nuts securing the element to the back of the oven, and resecuring after replacing with the new element. I did have to take the back panel off the oven to reattach the wiring to the element. This was necessary because while I was removing and replacing the element, the insulation was pulled through the access holes. I also replaced the temperature probe because I had already ordered it. This was easier to replace however and I did not encounter the isulation problem as I had when removing/replacing the element. I recommended your company to my friends and would definately order parts from you should I need to repair another appliance in the future. Thank you again.

Had a technician from Home Advisor to check the problem out with my Whirlpool Double oven(1 1/2 old). Paid $60 to find the problem. According to the technician problem was control board and cost of labor and parts $465.00
Jumped on Part Select website, placed a question with my stove problem through the chat. Immediately they answered my question and told me the problem was the Terminal Block. Cost of part and shipping $25.00. Replaced it myself and everything works fine.
Thank you, Thank you Part Select for your help and honesty.

Sincerely
Peter from Maryland

I slide the range out and unplugged it from the outlet. I removed the back of the oven ( 8 screws ) using a cordless drill and phillips bit then with a phillips screwdriver I removed the oven sensor (2 screws) then I installed the new sensor , reinstalled the oven back , plugged the range in , slide it back into place and that was it. This repair took about 10 mins and the oven works perfectly. Thanks !

See description listed as problem

took off nobs, pulled stove out 2 inches to access front side screws,( has 1 philip screw on each side end and four nut screws under panel) pulled panel out and flipped forward and down, all switches exposed and took apart broken switch and installed new switch(PAY ATTENTION TO WIRING PATTERN), reverse order for install back. bingo!

Had this range for 6 years. My daughter turned on the burner and it went "pop". She was very upset. I found the best price at PartSelect, and ordered the same day.

the first burner arrived broken in the box. We contacted PartSelect, and they immediately sent another and rushed shipping. It arrived in excellent condition.

To replace the unit: First, I turned off the circuit breaker for the range. Then I removed the two Philips screws that held the cooktop down. Next I removed the nut screws holding the burner to the cooktop.

Then I placed the new burner next to the old one, and one by one swapped the wires (this way I was sure I had the right wire on the right connector). One of the wire connectors broke when removing it from the old burner. PartSelect had provided 4 repacement connector pieces (oddly, all of which were too small for the burner element). So I located a replacement connector at a local hardware store. Stripped the end of the wire and used pliers to fasten the new connector.

After all connectors were secured to the new burner, I screwed the burner to the cooktop, then closed the cooktop and secured it with the two screws.

Turned on the circuit breaker, and it works like new! Saved over $100 by doing it myself!

Left oven off. Located sensor in pdf manual. Unscrewed mount, pulled sensor out to access connector. Disconnected old sensor, checked continuity(resistance) on ohms with multimeter. No continuity; connected new sensor, screwed mount back into place, turned on oven and baked cookies to check operation & it worked perfectly.

I looked it over and decided what i needed to have for parts .I ordered the new door handle from part select.com and within a reasonable time i received the part in the mail ...I lifted the door out of its place took the screws out put the handle in and buttoned it up ...The replacement part was as good as a new one would be...It took a matter of less than 30 minutes total... thanks for your service...

Repair was very simple. Took the door apart in layers, replaced the glass and put everything else back. it took longer to clean the stove than it did to actually take it apart and put it back together. guess i didnt need to be that much of a clean freak!

1. OPEN THE OVEN DOOR TO THE FIRST STOP,
PULL UPWARD TO REMOVE, ( IT WILL LIFT RIGHT
OFF)
2. LAY OVEN DOOR ON A FLAT SURFACE ( HANDLE
DOWN AND HANGING OFF SURFACE) WITH A
TOWEL TO PROTECT THE GLASS.
3. REMOVE ALL SCREWS AROUND THE
PERIMETER OF THE DOOR..
4. CAREFULLY SEPARATE THE DOOR FRONT AND
BOTTOM BRACKET BY SLIDING AWAY FROM
THE MAIN DOOR INNER-ASSEMBLY, ( THE
FRONT GLASS IS HELD BY THE TOP CHANNEL.
5. TURN THE MAIN DOOR INNER ASSEMBLY OVER
AND REMOVE THE HANDLE ASSEMBLY TWO
ATTACHING BRACKETS.
6. REMOVE THE ATTACHING BRACKETS FROM
THE HANDLE AND ATTACH TO THE NEW
HANDLE.
7. THE DOOR GLASSES CAN NOW BE CLEANED
8. ATTACH THE NEW HANDLE ASSEMBLY
9. REASSEMBLE IN REVERSE ORDER.
( BE CAREFUL WHEN SLIDING FRONT DOOR
GLASS INTO THE TOP DOOR CHANNEL}

I took the oven door apart, pulled out the broken fragments of glass and replaced it with the new glass. I should have taken notes as I took the door apart because it was a bit tricky to remember how all the pieces fit back together.

I was very impressed with how quickly the parts were shipped and the quality of the packing materials to protect the glass as it was shipped.

Purchased new bake element from PartsSelect. Very easy to install, unplug range, remove 6 screws, slide element out and unplug end, remove old element. Reverse procedure to install new element. My range was about 6 years old and in excellent condition, was considering buying a new range. Found PartsSelect on-line and ordered new element. Their website is very easy to use and find correct parts.
Saved lots of dollars, this PartsSelect website and service is great.

The plastic attachment on the oven door handle broke on one side, and of course the whole handle had to be replaced. I attempted first to super-glue the broken piece, but naturally, that didn't work. I found the necessary piece very easily thru PartSelect.com's web page, and had the replacement piece within a couple days. The most difficult part of the whole operation was figuring out how to remove the old handle. Once that was done, the replacement took approximately 15 minutes. Thanks PartSelect.

First I removed the screw behind the stove that hides the electrical wires. Pull off the two wires connecting the bake element with pliers. Unscrew the two screws holding down the floor pan which covers the baking element and pull out the floor pan. Here you will see the baking element, it is attached with a few screws. Remove the baking element and attach the new the same way.
We could not believe how easy this repair was to do. Not to mention all the money we saved on a repair man.
Thank you partselect.com, I'm glad I researched this on the net.