MER5765RAB1 Maytag Range - Instructions

It was easy to remove the old oven door gasket. Just a little tug was all that was needed. Installing new gasket was just as simple as tucking in the gasket end into the hole at the bottom and pushing the clip in the corresponding hole.
TIP: roll the end of the gasket and feed into the hole then use a small tipped screw driver or the point of a needle nose plier to finish installing the ends into the hole at the bottom of the door opening.

First I called a repairman and left a message. That was 3 weeks ago. So, I 'googled' the error message and determined what part I thought I needed. Ordered the part on Wednesday evening and it was there when I got home from work on Friday. I unpacked the part, got a phillips screwdriver and then watched the repair video on your website. About 20 minutes later I pushed my stove back in place and the flashing said 'set time'. Then I checked both ovens, and have since used both, and everything works!!

Door was removed very easily. Outside trim pieces were removed. The rest came apart like a simple puzzle. Inside glass is very easily accessed. Upon assembling, time was well under an hour. Shipping was fantastic and I saved close to 200dollars between a service call and a repair.

The sensor is mounted in the top right side of the oven.An extra long screw driver helps to avoid damage to the sensor when replacing it.The connectors were the opposite to the old sensor and I did not see that there were adapter cables included. It might help to connect or tie these together as I only expected the sensor and did not look for adapters.I had cut the wires and used wire nuts when I found the adapters.The repairs works fine.
Mike

Unplug appliance, unscrew small cover plate in rear. Disconnect wires from old element, may need to use needle nose pliers to wiggle clips off. Open oven door, remove false bottom to expose baking element. Remove baking element. Install new element, connect wires from rear, and replace covers and false bottom. Plug in appliance and test.

First of all, let me say how "Not Handy" I am when it comes to these things. I decided to give this part a try after my oven decided to fail on Thanksgiving Day, so I ordered the part. It arrived on time as promised and packaged very well. The on-line parts breakout and testimony from the other buyers were so helpful. I had our oven back up and running in less than 10 minutes.

One thing I would also recommend is that you burn the element once installed for at least 15 minutes to get the newness smell off of it and then it won't permeate your food items.

Thanks, Parts Select! You saved me over $900.00; the price it was going to cost me to buy a new oven. :)

removed the two screws in the rear of the oven to access the element. once exposed I removed the four screws holding the element in place. Went to the ouitside back of the stove and removed one screw holding the shield to access the terminals for the element. Installation was in reverse order.

Took screws out of the back on the side the sensor was on, unplugged it & took out the two screws on the inside of the oven to release the sensor. Put new sensor in place with the two screws & used one of the adapters to plug in the new sensor. Put screws back in the back panel & turned on the oven which unfortunately is still 50 degrees low. Need a new clock with computer which is out of stock & unavailable. I was an electrician for 25 years so didn't experience any problems. It was a cheap thing to try.

First I removed the oven door, then I removed the three screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then I connected the two wires to the new element , replaced the three holding screws and the oven door. ------END-------

The bake element in this oven is covered by a tray but after locating the screws for that and removing I could see the element was burnt so I just removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) then just reversed the procedure to install. Don't forget to unplug the unit first.

Found serial # as advised on web site. Found parts listing & ordered part. Got it in less than a week .
Unfastened two screws on top of door. Inserted glass. Applied a little mastic to prevent it from coming out again.
Done & done.
Do I get a prize ?

Turn of power to the range. The element lies beneath a metal cover. The cover is held down by two screws in each of the back cornors. The burner element is held by a screw in the the back and by two screws near the front. Replacing the element was a snap. With the screws removed, pull on the element until the connecting wires are exposed. Pull the wires from the element and attatch to new element. Replace screws, cover etc. Turn on power and note the time it takes to reach a preset temp. You may detect a slight oder form a coating on the new element. .

Pull oven away from wall and unplug. with the oven door open, remove 2 rear screws holding down the element cover and pull element cover out of the oven. remove 2 screws holding element down to the bottom of the stove, and one screw holding the back of the element to the rear. now go behind the oven and remove the access plate to the element power connection (one screw). Disconnect the 2 element power wires. remove element. to install, reverse these instructions

Turned off breakers to oven. Removed two screws that held oven in cabinet. Removed oven door by opening slightly and pulling up on door. Pulled oven out 1/3 of way. Took out four screws on top of control panel. Took oven light switch off by unscrewing holding ring. Removed temp knob on right by pulling. Removed start / stop knob same way.Removed glass straight out. Removed four screws that held elecrtonic clock conrtol board. Unpluged three wire plug from right side and the nine wire plug from the left side. Worked board out at and angle. Went backwards to connect and replace board, screws and door.Slid oven back in and tested oven after turning breakers back on, worked like new.

after i recieved the parts with the glass still laying on the foam pads it was packed in i put some soap on the bottom so the new bracket would slide on easier. i centered the bottom bracket on the bottom of glass and pushed in place. i then picked up glass and slid it up in place on oven door attached the screws on bottom done