CRE9830BCR Maytag Range - Instructions

Replaced the thermostat according to existing videos and had to adjust the thermostat using instuctions in the user manual for model CWE4800ACB.

I installed the new oven sensor but the problem continued. So I ordered a new relay board and installed it. Still no luck. So I pulled the new board back out and started trouble shooting it using my electronic background. I discovered the new board was using a pin for L2 that had no exit on the backplane, so I removed it and installed it where I believed it should go. Reinstalled the power relay board and presto. My oven is working lie a champ. Louis

I had to pull out the oven and balance the oven on two patio tables. Remove the back of the oven. Pull out the light assembly which was burnt. I was unable to remove the casing around the light, so I destroyed it with a pliers. Reinstalling the new light and assembly was easy. What made this job difficult, I could not remove the light assembly from the front of the oven and had to go in from the back.

With the back removed, replacing the lamp receptacle is straight-forward. Likewise, the door gasket is very easy. However, in order to replace the hinges, you have to remove the burner glass top (screws underneath the front lip), and inner and outer side panels. Also the supplied hinges mounting holes were not threaded so I had to use my own bolts, lock-washers and nuts in order to attach them. Total time, including a bit of cleaning, was 5 hours.

First, the diagram on your website said remove two screws. The diagram looked like they were on the back of the stove on each side. On my stove there were three screws that were visible under the front lip upon opening the oven door. I removed the top, which comes completely off and set it aside. Be careful when removing the top. Don't drag it out, otherwise you'll tear up the asbestos around the other burners. Two people would be better for the inexperienced people. The new elements have been redesigned, so the diagram doesn't fit what you are looking at. Plus, the diagram on paper is looking underneath the element when you are looking down on the top of the element. I removed one wire and put it in the same spot on the new. Turned out it was not the element that was bad. It was a loose wire in the inside of the control panel.

Removed old hinges, fabricated new mounting plates from 16ga steel plate. . . Cut new hinges to fit in available space. . . Drilled and tapped new mounting holes and adjustment tracks. . . Shortened existing springs to fit new configuration. Installed new hinges.

Pulled range out from cabinet-wall to get to back side, everthing was clearly exposed tlhen. Just a matter of installing new fixture, putting back on, reconnected power source - put range back in proper place.

Pulled the drawer and removed the oven door by pulling it upward. Then removed the two hex head screws which loosened the old hinge and pulled it down out of the side of the oven box. Replaced the new hinge in the position of the old one and installed the two hex head screws. I replaced the oven door and that was when I realized the part was wrong. The parts description in the view on the website was one number off and I replaced the broken hinge and ordered from another site the right number. That hinge works.

I followed peoples instructions here, and it was not very difficult.

Had to remove oven from mounting cabinet to get to the back since the wire lenght to the conector was to short to come through the mounting hole.
Other than that the repair was straight forward. 4 screws to dismount the Oven from cabinet, 2 screws to remove Sensor and 3 srews to open the back of the oven once out in the open. New cable adapter that came with the new sensor was needed in my case.

Flipped off breaker and removed oven door and pulled built in stove out so the back panel could be removed. Unplugged the sensor then removed the two screws securing the old sensor inside the oven and installed new sensor. Put stove back together and installed back into counter top, re-installed oven door, flipped on the breaker and oven works like new.

Replaced the long Oven Sensor but have not resolved the root problem. Oven still will not reach required temperature. Bottom element becomes red hot, but turns off and will not start again.

We actually had to get the repairman back that had repaired our microwave. Our range has the attached microwave above the range. My stovetop light worked prior to the visit. When he left, I prepared supper without the light, which did not go on. Ultimately, we had to replace the fluorscent tube, which thankfully, you had. No appliance store in a 35 mile radius did. We finally got the glass protector off, and the new tube did not go on. Back to the repairman, to tell him the new bulb did not work and that probably something happened when he visited before. He came back, found that indeed a wire had been broken when he was working on the microwave. I had indicated to him I did not expect to pay another repair bill after I had alrealy spent 117. before plus the cost of the new bulb, 22. something including shipping. He obliged and id not charge me anythink to repair the broken wire.
Now I have the old bulb for back up!!!
Thank you for having my replacement tube!!

The repair went very easy. I quickly removed the screws holding the frame to the oven door. The weight of the glass, held in place by the frame, pulled the unit off after the last screw was removed. The new part was "exact" and the reinstall went easily. The only caution would be to expect the weight of the glass in the door to pull down the frame after removal of screws!

Very easy to repair, but you have to be able to pull your stove out. Two screws in the oven and then remove part of back cover of oven and one plug from there. Simple to do, but did not fix our problem. We are waiting repair now from service company as it looks like it needs a control panel. Worth trying yourself to fix the problem. Inexpensive part and easy to install. Also be sure to turn power off your oven to reset the control panel as this may fix the problem - try this first and also after installing new part - like rebooting a computer...