MER6770ACW Maytag Range - Instructions

It's easy!!! I supervised my wife installing the element. She did great (probably because of my great supervision).

Checked online to see what F3 readout on stove meant. It meant replace sensor. Ordered part on a Sunday and part delivered Tuesday, Monday being MLK day. Detached bad sensor(2 screws inside oven)had to pull new sensor connector through hole from behind as insulation was too heavy (only removed 4 screws on right rear panel.Clipped wires together and reattached sensor inside oven. A cakewalk.

Slide stove out from wall and unplug. Remove two plastic side covers, (2 screws each outside, lossen Phillips screw on back panel and remove 1 screw each side under flange to release plastic trim). Remove two screws from lower lip in front of top. Pick up glass top rotating from front up first and pull forward to access and unplug burnner plug. Flip glass top over (carefull of broken glass falling out) Remove the two screws on each burner holding it to the top and snap out the "HOT" light assy. Transfer the four burners and all wiring as an assembly to the new top. Using a powered nut driver, screw the burners back into place on the new top and reinstall into stove. (New top did not have pre-threaded holes) While wife/girl friend cleans floor and stove before reassembly, enjoy a cold beer. Re-assemble in reverse order, have another beer.

First of all, I shut off the electricity to the stove.

I had to remove the two screws holding the stovetop in place. I then lifted it up and braced it to keep it from falling, removed the bad element, carefully marking the 4 wires that were connected to the element. I then disconnected the wires, and removed the two brackets holding the element in place. I replaced it with the new element, reconnected the wires, returned the stovetop to it's original place, put the two stovetop screws in, and turned on the electricity. Then I turned on the element, and it works just fine.

I ordered the part one afternoon. It arrived before noon the next day. Then I simply removed the old seal (with about 2 dozen spring clips). Inserted the new part by carefully inserting the new seal into its corresponding hole at each end and then worked my way around the seal while inserting each attached spring clip into its corresponding hole.

Removed stove top. Removed old element paying attention to wiring connections. Installed new element. Redconnected wiring. Put stove top back in place. Tested. Ate dinner.

Removed screws, pulled out element, disconnected wires, connected new element and screwed it in. 5 minutes tops. Best part is I ordered the part on Tuesday afternoon and it arrived Weds.... great company, Thanks!!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I connected the new element and screwed it into place.

Well all that was needed was to remove the two screws that held the element to the frame. I remove the screws and the two connection from the element. PLUG N PLAY. It's working and my wife is happy.

After searching on the internet for a very long time, we were almost ready to order the screws "blind" (no picture) from Sears for almost $10.oo per screw. Then I stumbled onto this website and found exactly what I was looking for, with a detailed description AND a picture!! Not to mention a price that was two thirds less than Sears..for TWO screws. Now the oven door is secure and we are no longer on our search for the right screws.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires to remove the old sensor. Went on line to find out where to order it from. Ordered it, It was on back order but was only about 1 week to receive. Reversed the procedure. WA LA. It works great.

My wife called a service company and was told that a tech would have to inspect the stove.
service charge 60.00 After inspection the parts would be orderd and a 200 fee for labor plus the parts would be charged at the completeion of the job. 2 weeks for part. I found you on the net orderd the glass. got it in 2 days and I completed the repair in 20 mins. Cost 89.00

It wasn't the handle that was broken, it was what the handle was attached to that was. I removed the door by opening to first detent and just lifting the door upward. Once off, I removed the screws on the top sides and underneath - a total of 9. This allowed me to remove the edging on the sides and underneath - the front glass came with it as well. Then I removed the Top trim by removing a screw on each of the sides and two on the front - this was the piece that was broken. Since I had already disassembled most of the door, I went ahead and dismatled the rest so that I could clean everything. The pieces that would fit went into the dishwaser and the rest (including the glass) I washed by hand (except the white insulation pieces of course). I did take apart the double glass panel by lifting up on a bent tab on one of the corners - this allowed me to clean the insides as well as the groves in which the glass sat. After everything was clean, I reassembled everything in the reverse order substituting the new trim for the old.

Notes: The top of the trim piece has two diferent screws - two short ones that screws into the trim piece itself and two that go through to the door metal. The screw that I ordered ended up being one of the short ones and I wanted the other. The snap nut was correct, and was what the longer screw to the trim actually grabs on to. I ended up using one of my own screws that fit like a dream, but wasn't painted white. The other note is that the sheet metal that the trim piece screws into from the front was slightly stripped. All I had to do was to place the metal on a hard surface and hit the holes with a hammer to bring them back into a usable form - not ideal, but worked nonetheless.

Removed the two screws holding the element in place. I then pulled the element and wiring out until I saw the connecter. I disconnected the two wires and then chose the correct connector from the package, snapped it back into place, put the screws back, turned on the breaker then tested the oven and found that everything was working correctly.
This is the second time I have ordered from Part Select, the first time was for a front LED panel on the same appliance. With the help finding the part you need and the comments from other customers I have saved a lot of money by repairing these problems myself. Oh, and the best part is the look on my husband's face when he came home and found out the repairs were made by me and not a repairman that he said I should call. He said he would laugh when the first repair by me didn't work but who's laughing now : )

As the video described I just unscrewed the sensor from inside the oven. Although I couldn't pull the wiring harness through the insulation (the wires were gathered in back with a wire tie) just four screws to loosen the back panel for access to the connection. My wife says it seems to be heating perfectly now.