MGR5875QDQ Maytag Range - Instructions

Removed the drawer from under the stove then unscrewed the access panel in the back (two phillips head screws). Rather than take it off altogether I just swung it to one side.

The ignitor electrical connector required two hands to disconnect and it was a bit of a reach but came apart easily enough once I got hold of it.

Removed the racks and bottom from the oven. the bottom is held in by two pins in the back that you just slide toward the front then lift it out. I did not bother to remove the oven door, but some people might.

Then removed the two hex head screws holding the ignitor on and pulled the connector out of the hole leading to the bottom.

Installation is the reverse of removal The electrical connector was reluctant to back down the hole, but went with a little wiggling and pulling from underneath. Once you get it back down there the connector is keyed, so you can't get it wrong.

Piece of cake, really.

Total repair time: about 30 minutes, including the mandatory halfway beer break.

Remove rear sheet metal cover. Disconnect the temp sensor wiring connector (on the left side as viewed from front).

Open oven, take out the 2 screws attaching sensor and remove. Reverse for installation.

Included wiring adapters are not needed for this model oven.

Ordered the broiler igniter that matched my model from part select and installed. Easy and part works as it should. Only took a few days to get here and saved me $40 by not purchasing at a local parts store as well. Will use part select if there are any future needs.

one screw holds the cover to the connector. one screw for the burner tube to the oven frame. two screws hold the ignitor bracket/assembly to the burner tube. that's it. take four screws off and disconnect. connect and put four screws back on.

Simple... unscrew the 2 screws and unplug the electrical connection to uninstall and just the opposite to install.

Put the back of stove on blocks of wood to get high enough to screw the new leg in.

ordered new broiler pan

Very Simple, I recommend pulling the old gasket in sections, and popping the new gasket metal holders in the holes as you go. You can't mess it up. For the ends, I tucked them in using a pair of needle nose pliers, but any small slender tool, such as a thin screwdriver, will work.

Unscrewed bottom piece; put on tape and new glass; re-installed bottom.

I shut the gas off and removed the oven door pulled the oven out and removed the electrical access panel.
unpluged the igniter and removed the 2 screws holding the igniter and relpaced repluged.
right to self clean mode. Easy job no worrys
Be safe check your gas connection!!

I removed the screws and unplugged the connectors and i inserted the new igniter which was glowwing much brighter than the old one which gave me an indication that it has the amount of temperature to open the gas valve.Idid a good job.

Nothing to it - remove oven bottom, and burner cover, unscrew the 2 scews holding the igniter
(one of mine sheared off now only one is holding the new igniter in - it still works) unplug wire at the connector then reverse and the oven is as good as new. The best part is that I received my part in only 2 days.

Remove oven door, pan drawer, oven racks, bottom pan, flame spreader. Remove valve cover at back of pan drawer. Unplug old igniter. Remove two mounting screws holding igniter to gas tube assembly. Install new igniter, plug it in, and reassemble. Easy as pie! Oven works better than it has for a looooong time! Heats up to 400 in 5 minutes. Wife is happy! :)

I removed the floor of the oven (one screw) and the heat dispersal shield (one wing nut). Then I detached the old igniter using a socket set. I had to remove the bottom drawer to unplug the ignitor and plug in the new one. Then I reassembled. Total piece of cake and I have no experience whatsoever.

Remove the oven door by opening halfway and lifting door away from stove. Removed racks and bottom pan from oven area exposing the gas bar and vertical mount igniter. Next remove bottom storage door. With phillips screwdriver remove 2 screws securing rear cover plate in back of storage area, accessing the igniter connection, and unplug the plug. Next back in oven, remove 2 5/16 sheet metal screws securing igniter with a nut driver and remove igniter by getly pulling disconnected end thru to oven. Now reverse process, install new vertical mount igniter and push connection down thru to storage area, then reconnect wire connection and put cover plate back on.
At this piont I turned oven on and checked igniter, it glowed red right away and the oven lit right up. Put storage door, oven door, bottom oven panel, and racks back in and done. Took 15 minutes tops, and anyone can do this, super easy. My oven would sometimes take half hour to preheat to 350,if it even lit, now 5 minutes, and it lights every time. Save the cost of a repair man folks, this one can be done by any weekend warrior.
I would just like to note....if you are uncomfortable with disconnecting wire plugs and plugging them back in, just unplug the oven from the wall as well before changing out the part, just to be safe.