MGR6751BDS Maytag Range - Instructions

After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.

First, I called Sears who wanted $440.00 to send a tech out to repair the stove. Second, I visited various web sites to find out what the problem was. I watched a brief video on Part Select which showed the repair of the stove. I then checked other parts stores on the web and selected Part Select based on price and video. Installation was very easy just as the video showed. Stove was repaired in less than 30 minutes.

My first suggestion, after turning off the power to the unit, is to take the oven door off. Two simple screws and it's off! It makes getting to the temperature sensor much easier. I also moved the oven out so I could get access to the back to remove the rear panel. The ordered part came with two pigtails, neither of which fit my oven wiring harness. I cut one of them and the wiring from the faulty sensor, spliced them together with wire nuts and made my own connection harness. The new sensor went in with little effort. The wiring went together flawlessly with the spliced connection protected between the oven cavity and rear panel. Reattached the rear panel and the oven door, then slid the oven back into place. Turned on the electricity and back to normal! Problem resolved!!

Undid screws on front and some on the back and replaced part and put screws back on and it fixed the proble

I had to pull the range out from the wall and loosen the rear cover to free the connector for the sensor as it got stuck on a corner guide. Put the new sensor in, rear cover back on, range back in place and tested the oven. Oven heats fast now and keeps a more even temp. Makes me wonder how long I was trying to cook with a bad sensor.

It was necessary to take the decorative glass and metal safety panel off using a screwdriver in order to get to the frame that holds the safety glass. It was hard to slide the new glass into the frame without help from a second person to hold the other pane in place.This was an easy repair to make I would just suggest having 2 people to hole things in place while replacing screws.

Ordered the oven sensor. Two screws to remove to replace old sensor. Since this was a slide in unit, you had direct access to the wiring harness. Used the adaptor. Total repair time about 20 minutes. A very easy do-it-yourself project.

Slide oven door off hinges. Remove old gasket. Instal new gasket. Used eraser end of pencil to help feed in ends of gasket into respective holes for excess. Note: job could have been accomplished without taking off door but I wanted to take door appart to clean inside and out of glass.

I lifted the burner tray from stove turned it upside down then removed six small screws from side of cover pan then I removed the cover then I removed the screws from the back of the old burners and igniter.Then I turned the old burner counter clockwise and it lifted out easly. the igniter is removed with no problem. The new burner is put in place and turned clockwise to lock in place.Then replace then the gas tubes and igniter and igniter wire then put tray cover on.

Removed oven door (slides out). Removed side and bottom screws from frame and slid new glass into place. screwed in the 8(or so) screws.

followed instructions and slid clips where instructed

This is a no brainer. I am only doing this because you asked. Pull out the stove, tilt it back, remove broken leg, install new leg.

Cut off the electricity at the junction box. Removed two screws from the sensor at the back of the oven. Then pulled the sensor with the wire out of the installation hole in the back of the oven. Disconnected the quick connect plug from the sensor and reconnected the new part. Reversed the process and screwed the two screens back into the oven wall. Turned the electricity back on and started up the oven. (Everything ran well for about three days when the oven again signaled "F-5" indicating the oven was again not functioning properly. Restarted the oven and is currently running properly. My spouse does a lot of baking with this oven for cookies, roasts, etc. Next time it fails I will be forced to call a repairman as I believe there is something wrong other then the heat sensor.

My wife watched the instruction video on the computer and replaced the oven sensor with a screwdriver in just a few minutes with no problems. Just make sure you order the right sensor. She ordered the short one by mistake and had to return it and order the Long Oven Sensor.

first the part was ordered but found it way too overpriced. went to an automotive store and bought door edge molding for a lot less. and it was better quality that the original gasket. with the self stick interior of the door edge molding was a fast and simple repair and more secure.