MES5770AAQ Maytag Range - Instructions

Hired a pro. Parts are difficult to get on a timely basis today , if at all. Screw up this repair by damaging the outer " black glass " and you buy a new stove. It took three weeks to get my replacement glass even though PS said the part was being sent within a day of the order. Even so , I am am happy to have gotten it , and will continue to use the company.

super easy after watching the how to video you had on it and iam the wife not the husband it was so easy thanks

Element was sent by buyer, As they recommended, when model of stove given to them. It was upper right rear. When element came. First took off old element. ...Match both element , new element did not look exactly the same, small variation. It did not come on.. I moved old element from left side to right side . Old element worked on both side .. tried new element on left side also.. still didn't work.. so I called right away and explained.. new element did not work.. not defective, but, just wasn't the right one.. I had a specialist came and check it out also. I was told wrong element.

Turned oven circuit breaker off. Removed oven racks. Removed 2 screws from old element. Pulled element out slightly disconnected wires on each end and reattached to new element. Pushed back in and reinstalled the 2 screws, reinstalled oven racks and turned circuit breaker back on. All done in about 20 minutes.

Removed front panel of range, removed switch (2 screws), unclipped wires from back of existing switch. Installed new switch - reverse order of above.

The sensor is mounted in the top right side of the oven.An extra long screw driver helps to avoid damage to the sensor when replacing it.The connectors were the opposite to the old sensor and I did not see that there were adapter cables included. It might help to connect or tie these together as I only expected the sensor and did not look for adapters.I had cut the wires and used wire nuts when I found the adapters.The repairs works fine.
Mike

We moved into a house with seemingly newer looking appliances. After the dishwasher broke and destroyed our floor, we found out that they were all twelve years old. Amazing the condition they were in after all that time.

The oven was the next thing to break. The hinge snapped, and while we could still use the oven, it allowed hot air to seep out.

So I checked online and lo and behold, I found a hinge for under $20. Wow. Much cheaper than a new range.

The most amazing thing was that I purchased it on a Friday afternoon, and it showed up on Saturday, so we could do the repair over the weekend. I cannot tell you how impressed I am with that kind of service.

We had to take off the side panel which was a pain, but all in all, it was 7-8 screws and swapping the hinge was easy. One of the screws did not want to go back in, so I had to find a replacement, but other than that, it was a pretty easy repair.

Thanks!

The replacement unit was a substitute part. Wiring slightly different. Instructions bare minimum. Follow instructions and it does work. No instructions as to how to remove the stove top. Been there before so sort of knew how. Nothing in the Jenn Air manual for stove top removal. The control panel has to be removed, two screws on each side and four hex screws on bottom, this allows for the disconnect of wiring for the top.
Remove the two trim pieces one on each side. One screw at top and one at bottom. The trim piece will move towards the rear and come off. Two screws on each side and two in the back will release the top. Remove top and lay on padded surface. You are ready to replace unit.

My genius scientist husband responsible all electric string connections, I responsible buy right parts and all support work, we worked as a team and fix the problems:) :)

removed old socket and replaced.
I was VERY pleased with Partselect. Easy to find part, it was in stock and fast delivery.

I did not mark wires with their associated numbered connections on the old burner but I did take pictures prior to removing the old burner. This slightly complicated finding the right connections for the wires on the new burner but the photos taken were invaluable in doing so. The placement of burner connections between new and old was different. Additionally, there were 2 connections on new and old that were not numbered. These turned out to be the power to the inner and outer coils and their connections were determined by examining the burners and connecting accordingly. Also, not mentioned in the instructions was a light on the new burner that the old burner did not have. I removed the light and the wire connecting it to the burner and connected the freed new burner connector based on the old/new burner connection numbering. Despite my lack of confidence that I correctly installed the burner, it worked on the first try and I am very happy to have it fully functional again.

Remove the door.
Remove screws
Clear out broken glass. Vacuum out small glass shards.
Clean all glass.
Reattach all parts.
Replace the door.
Smile!

Watch the video. Spot on instructions. Easy peasy.

oven had to completely come out cause two sheet metal side panels had to be removed to get to hinge.

Removed the two screws holding the sensor to the rear oven wall. pulled out sensor wire. It was caught on other wires behind the oven. removed the three screws holding the 8" inspection plate in the center of the rear panel. Carefully move the insulation and reach in to grasp the back end of the sensor wire. Once free from the snag it easily pulls out with the sensor just as stated in the video. using the appropriate adaptor it was easy to re-asseble and and attach to the oven wall. Replace the rear panel with the three screws and it was done