LCRE800 Maytag Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Daniel from Prescott, MI
- Parts Used:
- 7201P036-60
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Burned up oven door gasket needed replaced.
I started by removing the door, then trying to remove all of the screws in the oven casing. Of course the very middle screw in the bottom of the oven was rusted and dammged by use. I had to use a drill bit and remove the old screw. After dissasembly of the oven casing, I found that the lip that supports the gasket was rusted and burnt away about 3/4 in. I placed the new gasket in and found that when closed it covered this defect and sealed. I reassembled and cheked for operation.Ok! Imortant--remove the elements before removing oven casing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Houston, TX
- Parts Used:
- W10125458
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Uneven Heating/ High Heat Broiler To No Heat
After replacing heating element then selector switch, I came to think the only other thing was the thermostat. It finally worked. . . But not without some tribulations. This note is for a repair involving thermostat for a w130 jenn-air or maytag wall oven, do not follow instructions included with replacement part! It says the br and ba terminals are to be reversed with this replacement part. . . Not so! After re-connecting (as per instructions) nothing worked! If you have this model jennair or maytag, my suggestion is to replace the wires to connections just as they were removed from the old one. I finally did this after much frustration and electrical testing with a multimeter. Hope this note helps someone. Good luck!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yafa (and David) from Bothell, WA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Veronika from Pottstown, PA
- Parts Used:
- WP7711P357-60, WP7711P354-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
White Markings on Themostat & Selector Knob Wore Off
I ordered the new knobs, which arrived in a couple of days, pulled off the old ones and put on the new ones. Total time: less than one minute. I am very satisfied with the fast turn around time of this order. I would recommond this company.
V. White
Pottstown, PA
V. White
Pottstown, PA
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- OSCAR from BRISTOL, CT
- Parts Used:
- 7711P172-60
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replace clock-adjust knob
Although normally a push fit, we drilled and tapped a #6-32 cross hole and used a set-screw to attach the small knob.
The original knob is still hiding somewhere but, thanks to PartSelect we are back in business !
The original knob is still hiding somewhere but, thanks to PartSelect we are back in business !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- bernice from santa barbara, CA
- Parts Used:
- WP7711P357-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the white names on my selector knob had worn off.
I just pulled off the old knob and pushed on the new knob. My JENN-AIR Oven is 20 years old. The new knob is a different style and it doesn't fit snug against the oven. But it works and I can set the oven to Bake or Broil or clean and know I'm in the right place. I really like this oven and hope it will last another 20 years.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from Flemington, NJ
- Parts Used:
- 7201P015-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
lamp retainer gasket disintegrated when changed burned out bulb
I just removed the lamp retainer plate and glass cover, inserted the new gasket, and screwed everything back in place. Simple as that. I was enormously pleased that the part arrived so quickly -- just in time for me to cook my Thanksgiving turkey and use the self-cleaning feature.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Claudia from hewitt, TX
- Parts Used:
- WP7711P357-60, WP7711P354-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I cleaned the knobs and the numbers came off leaving me in a state of panic as I had no idea that would happen and could not even estimate the temperature.
Just took them out of the package removed the old ones and attached the new ones. I cut out a picture of the knob when the accident occurred, who would guess cleaning the knobs would erase the numbers, and taped the picture above the knob until the new ones arrived. thank you for keeping the old knobs in stock,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gerald from springboro, OH
- Parts Used:
- WP7711P354-60, 7201P015-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replace Oven Light
When replacing the bulb the gasket on the cover was destroyed . Replaced the gasket and screwed back on. Pulled knob off and replaced with the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JERRY from SPANISH FORK, UT
- Parts Used:
- WP95292
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old tube burned out
removed the shield and removed the old tube. Replaced with the new tube and replaced the shield. The only place I could locate this tube was through the internet. This Co. had as good a price including shipping that I found.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Geraldine M. from Fork Union, VA
- Parts Used:
- WP95292
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
my stovetop light did not work
We actually had to get the repairman back that had repaired our microwave. Our range has the attached microwave above the range. My stovetop light worked prior to the visit. When he left, I prepared supper without the light, which did not go on. Ultimately, we had to replace the fluorscent tube, which thankfully, you had. No appliance store in a 35 mile radius did. We finally got the glass protector off, and the new tube did not go on. Back to the repairman, to tell him the new bulb did not work and that probably something happened when he visited before. He came back, found that indeed a wire had been broken when he was working on the microwave. I had indicated to him I did not expect to pay another repair bill after I had alrealy spent 117. before plus the cost of the new bulb, 22. something including shipping. He obliged and id not charge me anythink to repair the broken wire.
Now I have the old bulb for back up!!!
Thank you for having my replacement tube!!
Now I have the old bulb for back up!!!
Thank you for having my replacement tube!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Billy from Grand Prairie, TX
- Parts Used:
- 7201P015-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replaced appliance bulb in owen
Removed burnt bulb. On replacing the bulb I glued the bracket, retainer gasket and bulb cover together- I used only a small amount of glue-just enough to hold the three items together. You need to do this since the three items slip in your hand while you attempt to screw the bracket to the oven wall. Need my help, email me @ Lexidog999@tx.rr.com
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Willi from Old Saybrook, CT
- Parts Used:
- WP7112P004-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Thermostat bulb was hanging loose
Removed what was left of the original clips. Pressed in the new clips and snapped in the themostat blub
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lois from St. Thomas, PA
- Parts Used:
- WP7711P354-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Oven Temp. Knob. on cleaning, the numbers were erased
Took one knob off and put the new one on .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Schwenksville, PA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
oven light burnt out
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
Was this instruction helpful to you?
Thank you for voting!