MERH752BAW Maytag Range - Instructions

Removed the oven door an removed some screws. After that it was pretty much self explanatory from there. Real simple project !

Access to burner nothing like on-line videos:

1) Remove 4 screws under front control panel. (Oven door needs to be open.)
2) Remove 2 flat head screws on sides of control panel. This will loosen control panel. Capture control panel to keep from hanging from wires/connectors. I used hooks made from a wire hanger.
3) Remove 2 screws to remove two steel panels on either side of stove.
4) Remove rear screw of the 2 front screws now exposed and 2 rear screws near top of stove.
5) Carefully flip over glass top being careful not to pull on the wires.
6) Identify burner to be replaced. Note 2 numbers where two clamps are attached to burner.
7) Using 3/8” nut driver, remove screws to allow removal of burner. Remove wires per included instructions. Remove burner.
8) Place new burner under clamps and align to the holes by the two numbers noted in step 6 above.
9) Connect wires to new burner as per included instructions.
10) Reverse removal steps.

Turned off breaker, moved unit and unplugged the unit. Safety first! Removed the oven door, removed two Phillips screws, pulled out the heating element, removed two clips.

Installed new element in reverse order. Put back the door. Plugged in unit, moved back into place and turned on breaker. Tested the oven, and it worked great. Maybe 20 mins total, very easy and saved at least 200 bucks vs calling a repair guy.

I found on youtube Also we marked each wire with masking tape 1A and 1B, 2A and 2B. The wires were the same color.

Removed cooktop, wiring and coil. Marked where wires went on limiter
tabs. Ordered coil 1200 Watt, received a 1500 one. Sent back to PS with prepaid shipping label {great}. New one had a different limiter tab arrangement. The instructions included warned this but doesn't tell you where to put the wiring. Instructions say to remove the old limiter and put it on the new coil but this can not be physically be done plus who would want an old limiter on a new coil.
Found a YOU TUBE video on how to test and place wires on limiter switches which shows the number letter sequence on the ceramic part. Maybe PS will put that info in their instructions. Coil works great !!

I checked out Maytag.com - found the parts page on my computer - found the top oven element - ordered it from Part Select - it arrived just a few days later......

Before it arrived, I removed the damaged electric element from top of oven - easy.

Oven was ready for me to install new element - the video on your website was perfect - it helped me remove the old & install the new element from Part Select. It took me about an hour.

Thank you for your fast service, good instructions & the video!

I'm an 84 year old female. Did this by myself! Thank you!

Was very difficult because door handle broke off on Holloween 2020. I looked into model number and ordered part same day. Money was taken out of my account almost immediately. Email said it would be sent out within 7-10 days. A while month went by. I emailed them twice asking about my order. They never got back to me.

So after 2 months, I posted a review on Facebook of my experience with this company. Within an hour of my review going up on Facebook, they contacted me and I gave them my order info. It was sent out the next day.

So the only reason they took care of it is because of the bad public review on Facebook that I posted.

They did refund me the shipping cost. But I will never use this company again. This never should have gotten as far as it did. The only reason they talked to me after they took my money is because of the bad public review.

Put the back of stove on blocks of wood to get high enough to screw the new leg in.

Simple Removed the broken element,put the new one in.

Able to get correct part!!!!

My daughter repaired it without any problems.

Got a bent metal coathook to temporarily release the oven door, removed the screws from the old probe, inserted the new one, and hooked it up, using the one of the plug adapters provided. Problem solved! The oven door latch was now disengaged, the oven would now accept temperature inputs, and the rear cooling fan (which wouldn't shut off) now turned off. That's a lot of things working better for less than $50!

Extremely simple repair to make. Move stove away from wall and disconnect power. Remove the oven racks. Remove the rear sheet metal panel covering the wiring harnesses. Caution: Sharp edges and corners on sheet metal.Sensor is located in upper left corner on rear oven wall. Using a long-shafted #2 Philips screwdriver, remove the two Philips head screws and gently pull the sensor 1" away from the oven wall. At this point, it will help to have an assist from someone while you are behind the range. Have the assistant gently tug on the sensor while you watch for wires moving on the rear of the range. After locating the sensor wires, gently disconnect the plastic connector clip. Note: plastic connectors become brittle with age and exposure to heat Move to front of range and gently remove sensor from rear wall by pulling the wiring through the oven wall. Before inserting the new sensor wire through the oven wall, "dry fit" the wiring connectors to see that the new sensor is a correct connection. Make connection, and secure the sensor to the rear oven wall with the two screws. Install racks, reinstall rear sheet metal panel, and connect the power. Set the oven baking temperature to a moderately low temp, 300 - 350 deg. to test the new sensor.

I received my glass panel realy quick from Part Select. It was an eansy job to install the new pane.
It took less than an hour. Thanks for Your prompt service.

The job itself isn't hard--just unscrew all the trim pieces holding the door together, remove the broken handle, and put in the new handle. There's nothing technical about it. The main thing is keeping track of the order that you take off various trim pieces and keeping the screws together with each piece. Because all the parts overlap in one way or another, you need them to go on in the right (reverse) order when you reassemble the door. Also, the job is MUCH easier to do if you take the door off the oven. I didn't at first see how to do that, and disassembled the door in place, which meant crawling around on the floor to reach the bottom pieces. But then I realized that the door simply lifts off of the two hinged arms at the bottom, and so I reassembled it with the door resting on the stove top. Much easier! You need to do a bit of wiggling to find the right motion to lift the door off, but once you do it comes off easily. Be aware that it's pretty heavy and you may want a second person to help. Putting it back on again can be a little tricky, because the hinges move; as soon as you get one side lined up, the other one wants to move away. But a little patience will get the job done.